## Abstract

By analyzing the Poisson equation describing the static behavior of membrane and bimorph deformable mirrors and biharmonic equation describing the continuous facesheet mirror with push-pull actuators, we found that to achieve a high quality correction of low-order aberrations these mirrors should have sufficient number of actuators positioned outside the correction aperture. In particular, any deformable mirror described by the Poisson equation requires at least two actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order. Any deformable mirror described by the biharmonic equation, such as a continuous facesheet mirror with push-pull actuators, requires at least four actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order, and these actuators should not be positioned on a single circle.

© 2008 Optical Society of America

## 1. Introduction

Deformable mirrors (DM) are potentially applicable for precision shaping of aspherical surfaces in imaging, laser optics and astronomy. Many of these applications require low-order optical surfaces to be dynamically formed with large amplitude and very high fidelity, in many cases exceeding the Rayleigh criterion. Practice shows that the increase of the number of actuators inside the deformable mirror aperture does not always lead to a complete elimination of the approximation error, as the precision of forming of a low-order aberration is limited by the high frequency actuator print-through effect. In this article, we formally analyze the necessary conditions for a high-quality correction of low-order aberrations considering the most popular types of mechanical deformable mirrors, with special attention paid to the minimization of the approximation error.

## 2. Differential equations describing the DM response

Since its introduction [1, 2], the DM technology has gone through an impressive evolution. At the moment of writing we can identify three major groups of DM:

The deformation φ(*x*,*y*) of a membrane DM satisfies the Poisson equation:

where Δ is the Laplace operator, *p* is the pressure caused by the actuators and *T* is the membrane tension. A similar equation Δ*φ*(*x*,*y*)=*kV*(*x*,*y*) describes the behavior of a bimorph DM [6] with a free edge, controlled by the voltage *V*, where *k* is the scaling coefficient depending on the DM design.

The deformation of a continuous facesheet DM with discrete push-pull actuators, in the thin plate approximation is described by the biharmonic equation [10]:

where *D* is the cylindrical stiffness, the force *p* describing the action of actuators satisfies the conditions of static equilibrium and *φ*(*x*,*y*) satisfies to some additional boundary conditions. Equation 2 assumes the plate has tip-tilt degrees of freedom in the points of attachment to the actuators.

To find the DM controls *p* corresponding to the deformation required, we need to apply the differential operator Δ(Δ^{2} for the continuous facesheet DM) to the function *φ*.

Substituting *φ*=*Z ^{m}_{n}*, where

*Z*is a Zernike polynomial with the radial order

^{m}_{n}_{n}and azimuthal order ±

*m*as defined in [11], we find (see Appendix A) that

for all Zernike polynomials *Z ^{m}_{n}* with

*n*=|

*m*| including piston, tip, tilt, astigmatism, trefoil, etc.; and

for all Zernike polynomials *Z ^{m}_{n}* with

*n*=|

*m*| and also with

*n*-2=|

*m*|, including piston, tip, tilt, defocus, astigmatism, trefoil, coma and some higher order aberrations. To give an example, Fig. 1 shows the shape of Zernike term

*Z*satisfying to both Eq. 3 and Eq. 4 and term

^{7}_{7}*Z*satisfying only to Eq. 4.

^{3}_{5}This result can be explained by the fact that Eq. 1, 2 describe the DM shape in terms of actions *p* defined only within the correction aperture, while some modes can be exactly defined only by actuators positioned outside the correction aperture. These modes cannot in principle be found as an exact solution of Eq. 1 or Eq. 2 in terms of non-zero correction actions *p* inside the correction aperture.

## 3. Requirements to the geometry of actuators

Practical correction of any aberration satisfying to Eq. 3 for a membrane and bimorph DM, or Eq. 4 for a thin-plate DM, performed only by the actuators positioned within the aperture, results in a “bumpy” approximation to the desired shape. To obtain a high quality correction, a certain number of actuators should be positioned outside of the DM aperture so that the conditions Eqs. 3, 4 are satisfied inside the aperture, while the external actuators produce the required boundary corrections. The number of these external actuators should be large enough to produce a sufficient number of independent modes.

It was shown in [12] that for any DM with *K _{m}* actuators one can find a corrector with

*K*≤

_{z}*K*modes, described by the Zernike polynomials, such that these two correctors will have equivalent performance in the correction of aberrations with certain pre-determined statistics. It is also well known that low-order Zernike terms usually have higher statistical weights than the higher-order terms in most natural and artificial aberration sources. Therefore it is important

_{m}to develop wavefront correctors with good performance of the correction of low-order Zernike terms. Counting the total number of terms in the Table 1, starting from the zero order *n*=0 and up, we see that the total number of low-order terms with *n*≤*N* is equal to (*N*
^{2}+3*N*+2)/2, thus the total number of actuators *K _{tot}* should satisfy the condition

The number of terms satisfying the condition Eq. 3 is equal to 2*N*+1 and the number of terms satisfying to the condition Eq. 4 is equal to 4*N*-2. Therefore, the number of actuators outside the working aperture of the membrane or a bimorph DM should satisfy the condition

while for a continuous facesheet DM the number of external actuators should satisfy the condition:

These formulae can be used in practical designs to define the minimum requirements to the numbers of actuators inside and outside the correcting aperture of the DM. For instance, to correct all low-order terms up to the degree *N*=4, a continuous faceplate DM should have at least *K _{total}*=(4*4+3*4+2)/2=15 actuators, of which at least 4*4-2=14 should be placed outside the working aperture, while in the same situation a membrane or a bimorph DM should have at least 2*4+1= 9 actuators placed outside the working aperture.

We also need to mention that the external actuators of a continuous faceplate DM should not be positioned on a single circle. There are two conditions on the contour of the correction area to be defined: *φ*|*S* and
$\frac{\partial \phi}{\partial r}{|}_{S}$, where *r* is the radial coordinate, and *S* is the boundary of the correction area. A non-zero radial derivative (second condition) can be satisfied only by two push-pull actuators positioned at different radial distances from the DM center. As a practical solution we suggest to place one half of the outside actuators on a circle, with equal azimuthal spacing between the actuators. The another half of the external actuators should be placed on a circle with a different radius, also uniformly distributed by the azimuthal coordinate. Although we are not sure that this geometry is optimal for each possible application, it seems to be quite practical. Membrane and bimorph DM can have all outside actuators positioned on a single circle, as only the deflection *φ*|*S* should be defined.

Since our expressions define only the lower limit for the actuator count, the numbers of actuators chosen for any practical design should be somewhat larger than defined by Eqs. 5, 6 and 7.

For a DM with relatively large number of actuators, Eqs. 6 and 7 have very simple interpretation: any DM described by the Poisson equation requires at least two actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order. Any DM described by the biharmonic equation requires at least four actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order, and these actuators should not be positioned on a single circle.

Equations. 1 and 2 describe the ideal model, while the mathematical descriptions of practical DM designs can be much more complicated. However, in a very general case, the linear elastic deformations of a solid body (excluding plastic deformations) are usually described by a linear differential operator of the second order or higher, therefore at least some basic modes will satisfy to conditions similar to Equations 3, 4. Therefore the essence of our analysis remains valid for all these cases, regardless the complexity of the mathematical description.

To verify our conclusions, we have built a numerical model that calculates the correction error for a thin-plate free-edge DM described by Eq. 2 and for membrane DM described by the Eq. 1. Figure 2 shows the residual *rms* correction error for a 37-ch continuous facesheet DM with push-pull actuators for low order Zernike polynomials *Z ^{m}_{n}* for three different values of the correction aperture

*R*=1; 0.8; 0.65. We used only positive values of the index

*m*as the negative values correspond to a

*π*/2 rotation of the aberration, it follows from the uniformity of the geometry of the DM actuators that the performance of the DM should be approximately the same for the positive and the negative values of

*m*. The correction quality of low-order aberrations is poor when the full aperture

*R*=1 is used and all actuators are positioned within the correction aperture. The quality improves significantly for smaller

*R*practically for all low-order aberrations, because the number of actuators inside the correction aperture decreases and the forces developed by these actuators decrease too, while the external actuators develop higher forces to form the modes satisfying the conditions Equations 3 and 4. Polynomials

*Z*

^{1}

_{7}and

*Z*

^{3}

_{7}do not satisfy to the Eq. 4, therefore the correction of these terms requires at least some actuators to be positioned within the correction aperture. For these modes, the correction quality is better for the full aperture

*R*=1 and the error increases for smaller correction apertures such as

*R*=0.8 and

*R*=0.65. For aperture

*R*=0.65, the DM provides good correction for all Zernike modes up to the 5-th order, because in this case we have 19 actuators positioned outside the correction aperture and the condition Eq. 7 is satisfied for

*N*=5.

Figure 3 shows the calculated residual *rms* correction error for a 37-ch membrane DM for low order Zernike polynomials *Z ^{m}_{n}* for three different values of the correction aperture

*R*=0.8; 0.6; 0.4. The actuator structure corresponds to the pattern used in OKO Technologies 15-mm 37-ch MMDM. The case

*R*=1 is not considered due to the fixed edge of the DM. The graph clearly shows that the correction quality improves significantly with the decrease of

*R*for all modes

*Z*with

^{m}_{n}*n*=

*m*, which can be explained by the increase in the number of actuators positioned outside the aperture. Correction of aberrations

*Z*

^{1}

_{7},

*Z*

^{3}

_{7}and

*Z*

^{0}

_{8}is strongly dependent on the number of internal actuators, resulting in optimal correction with

*R*=0,8 when the maximum number of actuators is positioned inside the correction aperture. All other modes require simultaneous correction with internal and external actuators, therefore the optimum correction is reached at

*R*=0.6.

## 4. Experimental verification

To confirm the validity of our conclusions, we experimentally measured the approximation error of a 30-mm 37-channel piezoelectric DM with a free edge for aperture values of *R*=0.92, 0.8, 0.65 and 0.5. The DM (produced by OKO Technologies, Delft, The Netherlands) was controlled in a feedback loop by the FrontSurferWF sensor (also produced by OKO Technologies). In the first stage, the DM was controlled to produce the best possible fit to coma with a PV amplitude of 1 *µ*m. In the second stage, the shape of the DM was measured by a high-resolution Hartmann-Shack sensor, and the *rms* error was calculated for the total surface deviation with respect to a flat *δ*
_{1}, and for the surface error with respect to coma *δ*
_{2}. The improvement factor *δ*
_{2}/*δ*
_{1} corresponds to the theoretically calculated correction errors for *Z*
^{1}
_{3} in the Fig. 2. Experimental and theoretical results are compared in Fig. 4. The experimental *rms* error of correction was reduced by a factor of ~3 when the correction aperture was reduced from *R*=0.92 to *R*=0.5, however this improvement is smaller than the expected theoretically factor of ~18. The difference can be partly explained by the the rms error of the feedback loop *δ _{f}* depending on a combination of factors, including the sensor noise, wavefront reconstruction errors, control voltage discretisation errors etc. In our measurements the feedback rms error accounted to approximately

*δ*~

_{f}*λ*/40 for the wavelength of

*λ*=633 nm. Another error factor is the stiffness of the DM actuators, resisting the rotations of the DM surface at the attachment points. Yet another error source is the actuator creep during the interval between the moment when the feedback loop was stopped and the moment theDM profile was measured. Accounting for these limiting factors, we conclude that our experiment demonstrated a good qualitative agreement with the theoretical model.

## 5. Conclusion

In conclusion, we wish to emphasize that a large number of actuators within the correction aperture of a DM does not automatically secure a high-quality correction of low-order aberrations and higher-order Zernike terms *Z ^{m}_{n}* with |

*m*|=

*n*and |

*m*|=

*n*-2. To achieve a high quality correction of all terms

*Z*up to the order

^{m}_{n}*n*=

*N*, the bimorph and membraneDM should have at least 2

*N*+1 and the continuous facesheet DM should have at least 4

*N*-2 actuators positioned outside the correction area. For large numbers of actuators, these expressions can be translated into simple rules for the minimum number of exterior actuators: any DMdescribed by the Poisson equation requires at least two actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order. Any DM described by the biharmonic equation, such as a continuous facesheet DM with push-pull actuators, requires at least four actuators to be placed outside the working aperture per period of the azimuthal aberration of the highest expected order, and these actuators should not be positioned on a single circle.

The requirement to have actuators outside the correction aperture results in a larger physical size of a deformable mirror, which may have implications in the design of portable and autonomous adaptive optical systems.

## Acknowledgments

The visit of A. Samokhin to Delft was funded by Dutch NWO VIDI grant on adaptive optics for the human vision. Authors are grateful to S. Grabarnik for the development of deformable mirror simulation software.

## A. Laplacian and bilaplacian of Zernike polynomials

In polar coordinates, any Zernike polynomial Z* ^{±m}_{n}* (

*ρ*,

*θ*) consists of terms ${\rho}_{\phantom{\rule{.9em}{0ex}}\phantom{\rule{.9em}{0ex}}\phantom{\rule{.2em}{0ex}}\phantom{\rule{.2em}{0ex}}\mathrm{sin}}^{l+m\mathrm{cos}}m\theta $, where

*l*is even and 0≤

*l*≤

*n-m*(see, for instance, [11]). Thus Z

^{±n}

_{n}(

*ρ*,

*θ*) consist only of one term ${\rho}_{\phantom{\rule{.6em}{0ex}}\phantom{\rule{.2em}{0ex}}\mathrm{sin}}^{n\mathrm{cos}}n\theta $, and Z

^{±(n-2)}(

*ρ*,

*θ*) consists only of two terms ${\rho}_{\phantom{\rule{.6em}{0ex}}\phantom{\rule{.2em}{0ex}}\mathrm{sin}}^{n\mathrm{cos}}\left(n-2\right)\theta $ and ${\rho}_{\phantom{\rule{.9em}{0ex}}\phantom{\rule{.9em}{0ex}}\phantom{\rule{.2em}{0ex}}\mathrm{sin}}^{n-2\mathrm{cos}}\left(n-2\right)\theta $ .

Consider now Laplacian Δ=∇^{2} and biharmonic operators applied to the terms of Zernike polynomials
${\rho}_{\phantom{\rule{.8em}{0ex}}\mathrm{sin}}^{n\mathrm{cos}}n\theta $ and ${\rho}_{\phantom{\rule{.6em}{0ex}}\mathrm{sin}}^{n\mathrm{cos}}\left(n-2\right)\theta $. From the expression of Laplacian in polar coordinates:

it immediately follows that

and

and, thus,

and

This proves that for every *n, n*≥0

and

**1. **H. Babcock, “The possibility of compensating astronomical seeing,” Publications of the Astronomical Society of the Pacific **65** (386), 229 (1953). [CrossRef]

**2. **V. Linnick, “On the principal possibility of the reduction of the influence of the atmosphere on the image of a star,” Optics and Spectroscopy (USSR) 3, 401 (1957). English translation in F. Merkle (Ed.),”Active and adaptive optics,” ESO Conference 48, 535 (1994).

**3. **R. P. Grosso and M. Yellin, “Membrane mirror as an adaptive optical element,” J. Opt. Soc. Am. **67**, 399 (1977). [CrossRef]

**4. **G. Vdovin and P Sarro, “Flexible mirror micromachined in silicon,” Appl. Opt. **34**, 2968 (1996). [CrossRef]

**5. **E. Steinhaus and S. G. Lipson, “Bimorph piezoelectric flexible mirror,” J. Opt. Soc. Am. **69**, 478–481 (1979). [CrossRef]

**6. **C. Schwartz, E. Ribak, and S. G. Lipson, “Bimorph adaptive mirrors and curvature sensing,” J. Opt. Soc. Am. A **11**, 895 (1994). [CrossRef]

**7. **R. H. Freeman and J. E. Pearson, “Deformable mirrors for all seasons and reasons,” Appl. Opt. **21**, 580 (1982). [CrossRef]

**8. **B. R. Oppenheimer, D. Palmer, R. Dekany, A. Sivaramakrishnan, M. Ealey, and T. Price, “Investigating a Xinξtics Inc. deformable mirror,” Proc. SPIE **3126**, 569–579 (1997). [CrossRef]

**9. **T. Bifano, “Mems wavefront correctors: Electromechanical theory and recent performance advances,” In “Adaptive Optics: Analysis and Methods/Computational Optical Sensing and Imaging/Information Photonics/Signal Recovery and Synthesis,” Topical Meetings on CD-ROM, Optical Society of America, page ATuD1 (2007).

**10. **S. Timoshenko and S. Woinowsky-Krieger, Theory of plates and shells, (McGraw-Hill, 1953).

**11. **M. Born and E. Wolf, Principles of Optics, (Pergamon Press, 1993).

**12. **M. Loktev, D.W. De Lima Monteiro, and G. Vdovin, “Comparison study of the performance of piston, thin plate and membrane mirrors for correction of turbulence-induced phase distortions,” Opt. Commun. **192**, 91 (2001). [CrossRef]