Abstract

All inorganic CsPbBr3 perovskite quantum dots (QDs) have been recognized as promising optical materials to fabricate green light emission devices because of their excellent optical performance. However, regular CsPbBr3 QDs with an oleic acid (OA) ligand show poor stability, which limits their practical application. We replaced the OA ligand in CsPbBr3 QDs with a 2-hexyldecanoic acid (DA) ligand and, in the synthesis, found that the new material has better optical properties than regular CsPbBr3 QDs (CsPbBr3-OA QDs). Due to the strong binding energy between the DA ligand and QDs, the ligand-modified CsPbBr3 QDs (CsPbBr3-DA QDs) show a high photoluminescence quantum yield (PLQY) of 96%, while the PLQY of CsPbBr3-OA QDs is 84%. Subsequently, the CsPbBr3 QDs coated on the blue light-emitting diode (LED) chips as green phosphors are demonstrated. The color conversion from blue to pure green is achieved by adding the CsPbBr3-OA QDs solution up to 60 μL, while the pure green emission devices only need 18 μL CsPbBr3-DA QDs solution under the same concentration. The ultrapure, highly efficient green light-emitting devices based on CsPbBr3-DA QDs exhibit a luminous efficiency of 43.6 lm/W with a CIE (0.2086, 0.7635) under a 15.3 mA driving current. In addition, the green emission wavelength of the devices based on CsPbBr3-DA QDs almost has no shift, even under a high injection current. These results highlight the promise of DA ligand-modified CsPbBr3 QDs for light-emitting devices and enrich the application field of ligand-modified CsPbBr3 QDs.

© 2020 Chinese Laser Press

1. INTRODUCTION

Light-emitting diodes (LEDs) have been recognized as efficient solid-state lighting sources and are widely used in the photoelectric field due to advantages such as high efficiency, a long lifetime, and a low power requirement. To improve the color-rendering index (Ra > 80) of white LEDs, the green and red contents in the spectra should be enlarged. In particular, the green light source is considered to have an important role in white LEDs [1]. Unfortunately, it is difficult to achieve high-efficiency green LEDs because of the well-known “green gap” problem [28]. In general, compared to the blue GaN-based LEDs counterparts, green GaN-based LEDs show much lower external quantum efficiency (EQE) and a stronger efficiency drop effect. To achieve efficient green LEDs, various efforts have been explored. For example, Saito et al. reported enhanced LEDs using the active layer consisting of the AlGaN interlayer and InGaN quantum well [9]. In addition, a series of studies about rare-earth-doped green phosphor materials also have been proposed [1013]. However, phosphor-based green LEDs still impede the practical application due to their poor monochromaticity and wide bandwidth [14,15]. Therefore, it is still necessary to develop high-efficiency green emission materials with good monochromaticity and a narrow bandwidth.

Recently, all-inorganic perovskite CsPbX3 (X=Cl, Br, I) quantum dots (QDs) have emerged as a new class of optical materials that have great potential for applications in the photoelectric field [1622], because of their high optical gain, narrow emission width, and high photoluminescence quantum yield (i.e., PLQY above 85%) [2327]. Moreover, recent reports using novel strategies on CsPbX3 QDs have enriched the applications. Ooi et al. [28] demonstrated the potential application of CsPbBr3 QDs for visible light communication. Their group also explored a high-speed UV color-converting photodetector based on CsPbBr3 [29]. Zeng’s group demonstrated that CsPbX3 QDs exhibit promising materials for high-definition QD displays and lighting devices [30]. Among the family of CsPbX3 QDs, CsPbBr3 QDs have been regarded as particularly promising for LEDs [31,32]. To date, much effort has been devoted to achieving green light emission using GaN-based LEDs that convert their blue or near-ultraviolet (UV) emission into green light via an interaction with inorganic CsPbBr3 perovskite QDs [22,33]. However, the reported CsPbBr3 QDs capped with long alkyl ligands such as oleic acid (OA) and oleylamine (OAM) synthesized by a hot-injection method exhibit unsatisfactory stabilities, which hinder their practical application in LEDs [34,35]. To improve the performance of LEDs based on CsPbBr3 QDs, some useful strategies have been proposed. The EQE of green CsPbBr3 perovskite QDs-based LEDs obviously could be enhanced through surface ligand engineering [36] and surface treatments [37,38]. Among those strategies, ligand modification of CsPbBr3 QDs also has been demonstrated to be an effective method to improve luminescent performance [39]. Replacing a long ligand (for example, an OA ligand) with a shorter ligand without degrading or destabilizing the perovskite structure is the key challenge for a CsPbBr3 QDs application. As presented in our previous report, we prepared high-quality CsPbBr3 QDs using a 2-hexyldecanoic acid (DA) with two short branched chains to replace an OA ligand with long chains in the synthesis process. During the process, the CsPbBr3 QDs with a DA ligand (CsPbBr3-DA QDs) exhibited more excellent stability and optical properties than the regular CsPbBr3 QDs with an OA ligand (CsPbBr3-OA QDs) [40]. However, to the best of our knowledge, there has been no report about CsPbBr3-DA QDs used as phosphors for green light emission devices. In this study, we aim to investigate the potential of modified CsPbBr3 QDs in light emission devices.

We synthesized high-performance CsPbBr3 QDs by using a shorter 2-hexyldecanoic acid (DA) ligand to replace an OA ligand for CsPbBr3 QDs. The ligand-modified CsPbBr3 QDs show a high PLQY of 96%, which were used as green phosphors for high-performance light emission devices. As a result, ultrapure and highly efficient green light-emitting devices based on CsPbBr3-DA QDs exhibit a luminous efficiency of 43.6 lm/W with a CIE (0.2086, 0.7635) under a 15.3 mA driving current. Furthermore, the green light-emitting devices based on CsPbBr3-DA QDs also have a more stable green emission than the devices based on CsPbBr3-OA QDs under various driving currents. Thus, we believe that ligand modification is an effective way to improve the performance of light emission devices.

2. EXPERIMENT

Chemicals and reagents: Cs2CO3 (99.9%) and PbBr2 (99.9%) were purchased from Xi’an Polymer Light Technology Corp. OAm (>90%, Adamas), OA (>90%, Adamas), DA (>98%, TCI), octadecene (ODE, >90%, Adamas) were used without further purification.

Synthesis of CsPbBr3-OA QDs and CsPbBr3-DA QDs: ODE (4 mL), Cs2CO3 (81.5 mg), and 0.5 mL OA were loaded into the 100 mL three-neck flask 1 with stirring; PbBr2 (0.188 mmol) and ODE (5 mL) were loaded into another 100 mL three-neck flask 2 with stirring. The two flasks were degassed at 120°C for 1 h under vacuum and nitrogen flow, then OA (0.5 mL) and OAm (0.5 mL) were quickly injected into flask 2, and the temperature rose to 150°C in 2 min in a nitrogen environment. A 0.4 mL of Cs-oleate solution was quickly injected. After 5 s, the crude reaction solution was cooled by the ice water bath. The synthesis of CsPbBr3-DA QDs was similar to that of CsPbBr3-OA QDs, except that the OA ligands were replaced by DA ligands.

Fabrication of CsPbBr3 QDs films: The QDs films were fabricated by spin-coating 400 μL of 10 mg/mL solution of CsPbBr3 QDs (in n-octane) onto glass substrates (1.5cm×1.5cm) in air. The speed of spin-coating was 2500 r/min (15 s). Thus, the 300nm thick CsPbBr3-OA QDs films could be obtained. The CsPbBr3-DA QDs films with the same thickness were also fabricated by this method.

Green LEDs fabrication: First, the 10 mg CsPbBr3 QDs were dissolved in 1 mL n-octane to obtain a homogenous solution. Then, the mixture was put in a vacuum chamber to get rid of the bubbles inside. Finally, the 6μL CsPbBr3 QDs solution was directly dropping-coated into the LED groove using a pipettor. Then, the LED was baked at 50°C to volatilize n-octane and to form the QDs layer. The thickness of the layer created by 6 μL QDs solution was estimated to be about 40 nm, and also the film thickness has a linear relationship with the dropped solution.

Materials and devices characterization: The X-ray diffraction (XRD) analysis was performed on XRD-6100 (Shimadzu, Japan). The purified samples were redispersed in 0.5 mL n-octane and then dropped on 0.8 cm by 0.8 cm glass substrates followed by solvent evaporation. The transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) images were performed using an electron microscope (Libra 200 FE, Carl Zeiss AG, Oberkochen, Germany). The absorption spectra were measured by a UV-vis spectrophotometer (UV-2100, Shimadzu, Kyoto, Japan). Samples with the same thickness were prepared by dropping the QDs solution (300 μL of 10 mg/mL solution of CsPbBr3 QDs) onto glass substrates. The photoluminescence (PL) measurements were conducted by a fluorescence spectrophotometer (Cary Eclipse, Agilent Technologies, Inc., Santa Clara, CA, USA) equipped with a Xe lamp. PL decay curves were detected using an EPL-405 nanosecond laser (Edinburgh Instruments Ltd., Livingston, Scotland, UK). The Fourier transform infrared (FTIR) analysis (KBr pellet method) was recorded using a Nicolet iS50 FTIR spectrometer (Thermo Fisher Scientific, Waltham, MA, USA). XPS spectra were recorded on a Thermo Fisher ESCALAB Xi+ spectrometer. The atomic force microscopy (AFM) images were analyzed by an atomic force microscope (MFP-3D-BIO, Asylum Research, Goleta, CA, USA). The characteristics of the fabricated LED devices were measured using one spectrograph of PR670 (Photo Research, New York, USA) with an analyzer system.

3. RESULTS AND DISCUSSION

A. Characterization of the CsPbBr3 QDs

The detailed synthesis of CsPbBr3-DA QDs can be found in the previous report [40]. The pristine CsPbBr3-OA QDs were synthesized via the general hot-injection method using lead bromide and cesium oleate as precursors [16]. The synthesis scheme of the modified CsPbBr3 QDs by using DA as a ligand to replace the regular OA ligand is schematically shown in Fig. 1(a). To confirm the successful synthesis of CsPbBr3 QDs with a DA ligand, HRTEM, XRD, and FTIR spectra were recorded. Figure 1(b) shows the XRD patterns of the CsPbBr3-OA QDs and CsPbBr3-DA QDs. Both samples exhibit distinctive XRD peaks at 2θ=15.2°, 21.5°, and 30.7°, which can be indexed to the (100), (110), and (200) planes of the CsPbBr3 cubic phase [4144], respectively. In addition, both XRD results of the CsPbBr3 QDs are well indexed to the standard cubic CsPbBr3 phase, without impure phases. It also can be seen that the crystallinities of the CsPbBr3-DA QDs are notably higher than that of the CsPbBr3-OA QDs. To investigate the surface ligand, the corresponding FTIR spectra were measured, as shown in Fig. 1(c). The peaks of CH3 reveal the presence of the ligand on the surface of both CsPbBr3 QDs. The peaks of 718cm1 are the peaks of -(CH2)- which are the long-chain saturated hydrocarbons, further confirming the presence of the ligands. In particular, the peaks of 1463cm1 (-COOH-) for DA ligand and OA ligand imply that the CsPbBr3 QDs are well capped with the OA/DA ligand after a cleaning process. HRTEM images reveal a cubic shape of the CsPbBr3-OA and CsPbBr3-DA QDs, with the average sizes of 11.66 nm and 12.44 nm, respectively [Fig. 1(d)]. In addition, the same lattice spacing of 0.58 nm for both CsPbBr3 QDs is clearly observed from the HRTEM images [Fig. 1(d)], which is consistent with the (200) crystal plane of the cubic CsPbBr3 structure. The HRTEM image also demonstrates that the CsPbBr3 QDs have high crystallinity. Interestingly, the CsPbBr3-DA QDs are found to exhibit a high PLQY of 96%, while the PLQY of CsPbBr3-OA QDs is only 84% [left inset of Fig. 1(d)].

 figure: Fig. 1.

Fig. 1. (a) Schematic illustration of the surface in the CsPbBr3 QDs with ligand modification process, (b) XRD patterns, (c) FTIR spectra, and (d) HRTEM images for CsPbBr3 QDs.

Download Full Size | PPT Slide | PDF

To better investigate the emitting properties of the CsPbBr3 QDs, we further conducted the absorption and PL spectra of CsPbBr3-OA and CsPbBr3-DA QDs films. Figure 2(a) shows the PL peak of both QDs centered at around 516 nm, while their corresponding absorption peaks [Fig. 2(b)] appear at around 509 nm, indicating a slight Stokes shift [45]. It is important to note the FWHM values obtained from the PL spectra are 20 nm and 17 nm for CsPbBr3-OA and CsPbBr3-DA QDs, respectively, indicating high-purity green emission for both QDs. Moreover, the PL intensity of CsPbBr3-DA QDs film is obviously enhanced under the same measurement condition. The time-resolved PL decay spectroscopy was used to study the lifetime of both QDs films. Biexponential behaviors are observed for both QDs films, indicating both QDs with the intact crystal structure and efficient radiative recombination. The inset table of Fig. 2(c) presents a summary of the comparison of the results for the two QDs consisting of a fast-decay component (τr), a slow-decay component (τnr), and the calculated average lifetime (τavg). Generally, the fast decay (τr) process originates from trap-assisted recombination, while the slow decay (τnr) process presents the free-charge carrier radiative recombination. CsPbBr3-DA QDs film shows an average lifetime (τavg) of 34.6 ns, which is much longer than those of CsPbBr3-OA QDs films (18.9 ns). The longer PL lifetime of CsPbBr3-DA QDs films indicates lower trap state densities, which may be ascribed to a reduction of the nonradiative pathways. To further demonstrate the formation of two CsPbBr3 QDs, the X-ray photoelectron spectroscopy (XPS) comparative analyses of CsPbBr3-OA and CsPbBr3-DA QDs were performed. The result reveals that both CsPbBr3-OA QDs and CsPbBr3-DA QDs are comprised of Cs, Pb, and Br elements, shown in Fig. 2(d). Both CsPbBr3-OA and CsPbBr3-DA QDs comprise all peaks labeled, which are consistent with the previous report [46]. The high-resolution XPS spectra corresponding to the core levels of Cs 3d (723.5 and 737.5 eV), Pb 4f (137.4 and 142.2 eV), and Br 3d (68 eV) are recorded [see Figs. 2(e), 2(f), and 2(g)]. The XPS results show no differences for both CsPbBr3 QDs, implying that their formation is well identified and both of them have been successfully synthesized.

 figure: Fig. 2.

Fig. 2. (a) PL spectra, (b) absorption spectra, and (c) lifetime of the CsPbBr3 QDs films. (d) XPS survey spectra of CsPbBr3 QDs. (e) Cs-3d spectrum, (f) Pb-4f spectrum, and (g) Br-3d spectrum. All peaks were calibrated using C 1s (284.8 eV).

Download Full Size | PPT Slide | PDF

The morphology of the CsPbBr3 QDs films plays a very important role in achieving a bright green LED. To further probe the film qualities of the CsPbBr3-OA QDs and CsPbBr3-DA QDs films, we used AFM to characterize the morphology of CsPbBr3-OA and CsPbBr3-DA QDs films. Figure 3(a) shows that the CsPbBr3-OA QDs film has a poor morphology with a high root mean square (RMS) surface average roughness of RMS5.61nm. However, after the DA ligand modification, CsPbBr3-DA QDs perovskite films with better morphology are obtained and show a significant reduction in the RMS roughness; namely 3.26 nm for the CsPbBr3-DA QDs films [see Fig. 3(b)].

 figure: Fig. 3.

Fig. 3. AFM images of the (a) CsPbBr3-OA and (b) CsPbBr3-DA QDs films.

Download Full Size | PPT Slide | PDF

B. Optical Properties of the Green LEDs

To demonstrate the green light emission conversion of QDs, the blue LEDs with an emission wavelength of 450 nm were used as an excitation source. The green LED devices were fabricated using CsPbBr3-OA QDs and CsPbBr3-DA QDs films as the active layer. We have designed a series of CsPbBr3 QDs layers to explore the suitable quantity for the green LEDs and obtain nearly pure green emission. The emission spectrum of both CsPbBr3 QDs as-coated LEDs has been recorded under room temperature. Figures 4(a) and 4(b) present the evolution of QDs coated on LEDs under the ambient conditions. Both of them undergo a change from blue to green light, indicating the CsPbBr3 QDs layers have a favorable color conversion ability that converts blue light emission into a green one. Finally, the green light emission of the CsPbBr3-OA QDs coated LEDs has a weak brightness, while the green LEDs with CsPbBr3-DA QDs are much brighter with less QDs solution. Both CsPbBr3-OA QDs and CsPbBr3-DA QDs based LEDs have been explored under a constant driving current of 31.1 mA during the coating process. The spectrum variation in the processing of LEDs with different amounts of QDs is shown in Fig. 4(c). The two emission peaks of 450 nm and 530nm are contributed by the blue InGaN chips and CsPbBr3-OA QDs, respectively. The quantity of the QDs solution addition is a key parameter for pure green LEDs. With an increase of the quantity of the QDs solution, the main blue emission peak of 450 nm reduces gradually, accompanied by an increase in the green emission intensity. Finally, the blue emission peak of 450 nm almost disappears and the green emission peak of 530 nm becomes the main peak, implying that the QDs enable absorption of the emission of the blue InGaN chip completely and output the green emission intensively. It is obvious that the intensity of green emission increases to a maximum value with the CsPbBr3-OA QDs up to 18 μL and then decreases with the addition of the QDs. Similarly, the addition of the CsPbBr3-DA QDs onto blue LEDs causes a similar emission behavior. Compared to CsPbBr3-OA QDs, a much smaller amount of the CsPbBr3-DA QDs solution is required for pure green emission. In other words, the thickness of CsPbBr3-DA QDs films is smaller than that of CsPbBr3-OA QDs films due to the different amounts of the QDs solution required under the same experimental conditions [including the concentration (10 mg/mL), room temperature and air]. We ascribe this to the higher PLQY of CsPbBr3-DA QDs solution.

 figure: Fig. 4.

Fig. 4. (a) and (b) Evolution of CsPbBr3 QDs coated on LED chips. The optical properties of (c)–(e) CsPbBr3-OA QDs and (f)–(h) CsPbBr3-DA QDs coated on LED chips. (c) and (f) Emission spectra, (d) and (g) green light purity analyses, and (e) and (h) behaviors of chromaticity coordinates with the addition of QDs solution.

Download Full Size | PPT Slide | PDF

In the presence of light-emitting components, the emission colors can be analyzed by a spectrum that shows the corresponding integrated intensity of the blue and green lights. As shown in Figs. 4(d) and 4(g), the percentage of CsPbBr3-OA QDs based green emission increases with the amount of QDs. The energy transfer efficiency from blue to green light is presumed to be important for achieving a green LED and estimated by the ratio of the light integration. For example, it is calculated to be 79.4% at 24 μL. The figures reveal that the coated LEDs exhibit nearly pure green light when the coated volume of the CsPbBr3-OA QDs and the CsPbBr3-DA QDs solutions reaches 60 μL and 18 μL, respectively. The smaller required amount of the CsPbBr3-DA QDs solution can be attributed to the better optical properties of the CsPbBr3-DA QDs compared to the CsPbBr3-OA QDs. Furthermore, the intensity of the green light from LEDs based on CsPbBr3-OA QDs increases slowly. We ascribe this phenomenon to the aggregation of the CsPbBr3-OA QDs during the emitting process, while the CsPbBr3-DA QDs might maintain better stability. We have confirmed that there is strong binding energy between the DA ligand and the QDs in our previous report; thus, the ligand could not lose easily during the emission process [40]. To investigate the quantification of the green emission light of the QDs coated LED, we have explored the light purity analyses on both CsPbBr3-OA QDs and CsPbBr3-DA QDs samples [Figs. 4(d) and 4(g)]. From blue to green, the color variation of the CsPbBr3-OA samples is achieved by adding the QDs solution up to 60 μL, while the CsPbBr3-DA samples change into the green region with only 18 μL. In terms of the calculation about light purity, the dominant wavelength plays an important role in the characterizing of the spectral light, and it can be speculated by the coordinates of the QDs coated LED and pure green light in the Commission Internationale Ed I’eclairage (CIE) diagram. Figures 4(e) and 4(h) show the CIE chromaticity coordinates of the spectrum, which reveals the process from blue to nearly pure green, with the increasing volume of the QDs solution. Finally, the chromaticity coordinates of the nearly pure green LEDs are reached at (0.2547, 0.7266) and (0.2086, 0.7635) for CsPbBr3-OA and CsPbBr3-DA QDs films, respectively. In addition, it is worth noting that the emission wavelength of the CsPbBr3-OA QDs red shifted from 525 to 536 nm along with the addition of the solution, while the CsPbBr3-DA QDs showed a small red shift. These red shifts can be ascribed to the QDs particles aggregation in solid-state, which is caused by the high temperature during the process.

C. Optoelectronic Properties

To further reveal the properties of the pure green emission, the emission spectra of the green LEDs under different currents have been measured. The voltage-current characteristics and the FWHM of both CsPbBr3-OA QDs and CsPbBr3-DA QDs coated on blue LEDs have been investigated. As shown in Figs. 5(a) and 5(d), the intensity of the pure green light increases gradually for both green LEDs along with the driving current increase from 0.4 mA to 64.7 mA. For CsPbBr3-OA QDs coated LEDs, the FWHM varies from 17 to 20 nm and the emission peak position changes from 538 to 540 nm when the driving current increases from 0.4 to 64.7 mA. The changes could be attributed to the aggregation of the CsPbBr3-OA QDs under high temperatures induced by the increasing current [Fig. 5(b)]. This phenomenon of thermally induced aggregation of CsPbBr3 QDs has also been reported in other previous research [4749]. In contrast, CsPbBr3-DA QDs coated LEDs exhibit robust stabilities even under a high injection current (i.e., the FWHM remains 22 nm and the emission peak keeps the same position, respectively), as shown in Fig. 5(e). The corresponding CIE coordinates of the CsPbBr3-OA QDs coated LEDs and CsPbBr3-DA coated LEDs are (0.2547, 0.7266) and (0.2086, 0.7635), respectively, exhibiting no shift under the different injection current, as shown in Figs. 5(c) and 5(f). Notably, the power efficiency (43.6 lm/W) of CsPbBr3-DA QDs coated LEDs is much higher than that of the CsPbBr3-OA QDs coated LEDs (30.9 lm/W) under a 15.3 mA driving current. These results demonstrate that DA ligand modification for CsPbBr3 QDs is a useful strategy to improve the performance of green LED devices.

 figure: Fig. 5.

Fig. 5. Optical properties of QDs coated on blue LEDs. (a) and (d) Spectrum intensity, (b) and (e) FWHM, and (c) and (f) behaviors of chromaticity coordinates under different injection currents.

Download Full Size | PPT Slide | PDF

4. CONCLUSION

In summary, we have demonstrated that CsPbBr3 QDs with DA ligand modification exhibit better properties than CsPbBr3 QDs with a traditional OA ligand. Subsequently, we have fabricated green LEDs based on both CsPbBr3-OA QDs and CsPbBr3-DA QDs under the ambient conditions. Compared to CsPbBr3-OA QDs coated LEDs, the LEDs coated by CsPbBr3-DA QDs show higher purity, higher thermal stability, and stronger green light intensity. This work promotes the investigation of LEDs based on ligand-modified perovskite QDs.

Funding

National Natural Science Foundation of China (11974063); Fundamental Research Funds for the Central Universities (2019CDJGFGD001); Graduate Scientific Research and Innovation Foundation of Chongqing (CYB19036).

Disclosures

The authors declare that there are no conflicts of interest related to this paper.

References

1. J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017). [CrossRef]  

2. M. R. Krames, O. B. Shchekin, R. Mueller-Mach, G. Mueller, L. Zhou, G. Harbers, and M. G. Craford, “Status and future of high-power light-emitting diodes for solid-state lighting,” J. Display Technol. 3, 160–175 (2007). [CrossRef]  

3. S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995). [CrossRef]  

4. A. Liu, A. Khanna, P. S. Dutta, and M. Shur, “Red-blue-green solid state light sources using a narrow line-width green phosphor,” Opt. Express 23, A309–A315 (2015). [CrossRef]  

5. T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011). [CrossRef]  

6. Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016). [CrossRef]  

7. I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018). [CrossRef]  

8. F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016). [CrossRef]  

9. S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013). [CrossRef]  

10. D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017). [CrossRef]  

11. M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018). [CrossRef]  

12. Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016). [CrossRef]  

13. Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018). [CrossRef]  

14. Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016). [CrossRef]  

15. H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015). [CrossRef]  

16. L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015). [CrossRef]  

17. J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016). [CrossRef]  

18. S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015). [CrossRef]  

19. A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015). [CrossRef]  

20. J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017). [CrossRef]  

21. Y. Zhang, H. Zhu, T. Huang, Z. Song, and S. Ruan, “Radiation-pressure-induced photoluminescence enhancement of all-inorganic perovskite CsPbBr3 quantum dots,” Photon. Res. 7, 837–846 (2019). [CrossRef]  

22. X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016). [CrossRef]  

23. S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015). [CrossRef]  

24. J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015). [CrossRef]  

25. G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015). [CrossRef]  

26. K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015). [CrossRef]  

27. B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016). [CrossRef]  

28. I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016). [CrossRef]  

29. C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019). [CrossRef]  

30. F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018). [CrossRef]  

31. S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016). [CrossRef]  

32. H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020). [CrossRef]  

33. C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016). [CrossRef]  

34. J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015). [CrossRef]  

35. Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014). [CrossRef]  

36. J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016). [CrossRef]  

37. X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016). [CrossRef]  

38. C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017). [CrossRef]  

39. H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018). [CrossRef]  

40. D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019). [CrossRef]  

41. L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019). [CrossRef]  

42. C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019). [CrossRef]  

43. Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018). [CrossRef]  

44. Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018). [CrossRef]  

45. M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017). [CrossRef]  

46. M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017). [CrossRef]  

47. I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016). [CrossRef]  

48. B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017). [CrossRef]  

49. S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018). [CrossRef]  

References

  • View by:

  1. J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
    [Crossref]
  2. M. R. Krames, O. B. Shchekin, R. Mueller-Mach, G. Mueller, L. Zhou, G. Harbers, and M. G. Craford, “Status and future of high-power light-emitting diodes for solid-state lighting,” J. Display Technol. 3, 160–175 (2007).
    [Crossref]
  3. S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
    [Crossref]
  4. A. Liu, A. Khanna, P. S. Dutta, and M. Shur, “Red-blue-green solid state light sources using a narrow line-width green phosphor,” Opt. Express 23, A309–A315 (2015).
    [Crossref]
  5. T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
    [Crossref]
  6. Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
    [Crossref]
  7. I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
    [Crossref]
  8. F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
    [Crossref]
  9. S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
    [Crossref]
  10. D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
    [Crossref]
  11. M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
    [Crossref]
  12. Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
    [Crossref]
  13. Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
    [Crossref]
  14. Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
    [Crossref]
  15. H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
    [Crossref]
  16. L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
    [Crossref]
  17. J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
    [Crossref]
  18. S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
    [Crossref]
  19. A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
    [Crossref]
  20. J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
    [Crossref]
  21. Y. Zhang, H. Zhu, T. Huang, Z. Song, and S. Ruan, “Radiation-pressure-induced photoluminescence enhancement of all-inorganic perovskite CsPbBr3 quantum dots,” Photon. Res. 7, 837–846 (2019).
    [Crossref]
  22. X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
    [Crossref]
  23. S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015).
    [Crossref]
  24. J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
    [Crossref]
  25. G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
    [Crossref]
  26. K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
    [Crossref]
  27. B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016).
    [Crossref]
  28. I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
    [Crossref]
  29. C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
    [Crossref]
  30. F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
    [Crossref]
  31. S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
    [Crossref]
  32. H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
    [Crossref]
  33. C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016).
    [Crossref]
  34. J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
    [Crossref]
  35. Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
    [Crossref]
  36. J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
    [Crossref]
  37. X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
    [Crossref]
  38. C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
    [Crossref]
  39. H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
    [Crossref]
  40. D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
    [Crossref]
  41. L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
    [Crossref]
  42. C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
    [Crossref]
  43. Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
    [Crossref]
  44. Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
    [Crossref]
  45. M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
    [Crossref]
  46. M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
    [Crossref]
  47. I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
    [Crossref]
  48. B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
    [Crossref]
  49. S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
    [Crossref]

2020 (1)

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

2019 (5)

Y. Zhang, H. Zhu, T. Huang, Z. Song, and S. Ruan, “Radiation-pressure-induced photoluminescence enhancement of all-inorganic perovskite CsPbBr3 quantum dots,” Photon. Res. 7, 837–846 (2019).
[Crossref]

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

2018 (8)

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

2017 (7)

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

2016 (13)

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016).
[Crossref]

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

2015 (10)

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

A. Liu, A. Khanna, P. S. Dutta, and M. Shur, “Red-blue-green solid state light sources using a narrow line-width green phosphor,” Opt. Express 23, A309–A315 (2015).
[Crossref]

S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

2014 (1)

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

2013 (1)

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

2011 (1)

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

2007 (1)

1995 (1)

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Abdelhady, A. L.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

Adinolfi, V.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Alarousu, E.

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Alexander, D.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Alias, M. S.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

Alyami, N.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Alyami, N. M.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Amassian, A.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Aygüler, M. F.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Bakr, O. M.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Bals, S.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Ban, M.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Biju, P. R.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Bladt, E.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Bodnarchuk, M. I.

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

Boix, P. P.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Bremers, H.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Brennan, M. C.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Cai, B.

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Cai, Z.

Callsen, G.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Caputo, R.

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

Carey, G.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Chang, Y.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Chen, C.

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Chen, W.

Cho, J.

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

Chowdhury, A.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Chulliyil, R.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Colvin, V. L.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Comin, R.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Craford, M. G.

De Luca, G.

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

De Roo, J.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

deMello, A. J.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

Diroll, B. T.

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

Docampo, P.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Dong, H.

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Dong, Y.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Draguta, S.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Du, J.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

Duhm, S.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Dursun, I.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Dutta, P. S.

Emiroglu, D. B.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

Fang, T.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

Feldmann, J.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Fiebig, M.

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

Galler, B.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Gao, X.

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

Gao, Y.

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Geiregat, P.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Grotevent, M. J.

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

Gu, Y.

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Guan, H.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

Han, B.

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

Han, J.

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Han, Y.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Hangleiter, A.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Hao, Z.

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Harbers, G.

Hashimoto, R.

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

He, Y.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Hedhili, M. N.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Heiss, W.

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

Hendon, C. H.

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

Hens, Z.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Herr, J. E.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Hill, I.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Hintermayr, V. A.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Hoffmann, A.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Hoffmann, L.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Hoogland, S.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Hu, W.

Hu, Z.

Huang, T.

Humer, M.

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

Hwang, J.

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

Ibáñez, M.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Irfanullah, M.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Ittyachen, M. A.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Iwasa, N.

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Jiang, H.

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

Jiang, J.

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

Jiang, M.

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

Jiang, X.

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

Jiang, Y.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Jin, Y.

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

Jönen, H.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Joseph, C.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Kang, C. H.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Kang, Z.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Karpov, S. Y.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Kemp, K. W.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Ketzer, F. A.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Khanna, A.

Kim, D. H.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Kim, J. K.

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

Kirmani, A. R.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Kong, D.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Kong, M.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Kovalenko, M. V.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

Krames, M. R.

Krieg, F.

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

Kruse, A.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Kuno, M.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Kure, T.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Labelle, A.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Langer, T.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Leng, Y.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Li, C.

Li, G.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Li, J.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Li, K.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Li, M.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Li, X.

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Lian, T.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Liang, G.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Liao, G.

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Liao, H.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

Liao, L.-S.

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

Lignos, I.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

Lin, C. H.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Lin, Z.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Liu, A.

Liu, G.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Liu, H.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Liu, J.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Liu, M.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Liu, Q.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Liu, X.

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016).
[Crossref]

Liu, Y.

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

Liu, Z.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Lu, C.-H.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Lu, M.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Lu, Z. H.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Lugauer, H.-J.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Luo, Y.

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Maceiczyk, R.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

Maes, J.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Maity, P.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Mani, K. P.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Manzi, A.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Martins, J. C.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Mathews, N.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Meng, H.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Mhaisalkar, S. G.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Miao, J.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Milowska, K. Z.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Minor, J.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Mohammed, O. F.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Mueller, G.

Mueller-Mach, R.

Murali, B.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Nag, A.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Nagahama, S.-I.

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Nakamura, S.

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Nedelcu, G.

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

Nenstiel, C.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Ng, T. K.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Nguyen-Beck, T. S.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Ning, L.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

Ning, Z.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Nippert, F.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Nunoue, S.

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

Ooi, B. S.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Ooi, E.-N.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Pan, G.-H.

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Pan, J.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Parida, M. R.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Park, J. H.

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

Parkhill, J.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Pecunia, V.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Peng, W.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Polavarapu, L.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Priante, D.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

Protesescu, L.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

Quan, L. N.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Ravi, V. K.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Ren, Y.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Rollny, L.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Rossow, U.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Rouvimov, S.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Ruan, S.

Saidaminov, M. I.

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

Saito, S.

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

Sargent, E. H.

B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Sarmah, S. P.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Schaller, R. D.

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

Schneider, S.

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

Schubert, E. F.

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

Schwiegel, A.

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Senoh, M.

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Shang, Q.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Shchekin, O. B.

Shen, C.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

Shi, T.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Shur, M.

Sinatra, L.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Sisira, S.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Snaith, H. J.

S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015).
[Crossref]

Song, J.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Song, T.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Song, Z.

Stavrakis, S.

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

Stranks, S. D.

S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015).
[Crossref]

Straßburg, M.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Sum, T. C.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Sun, B.

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Sun, C.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Sun, J.

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

Sun, J.-P.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Sun, K.

Sun, X.

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Sun, X. W.

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Sutherland, B.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Sutherland, B. R.

B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016).
[Crossref]

Swarnkar, A.

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Tang, J.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Tang, X.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016).
[Crossref]

Tang, Z.

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Thadhani, N.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Thomas, K.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Tian, Q.-S.

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

Tong, Y.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Tsukruk, V. V.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Unnikrishnan, N. V.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Urban, A. S.

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

Van Driessche, I.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Veldhuis, S. A.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Vimal, G.

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Voznyy, O.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Wagner, B. K.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Wagner, M. R.

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Walravens, W.

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

Walsh, A.

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

Wang, C.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Wang, H.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

Wang, J.

Wang, K.

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Wang, M.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

Wang, Q.

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

Wang, Z.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Wang, Z.-K.

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

Wu, C.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Wu, H.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Wu, K.

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

Wu, T.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

Wu, Y.

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Xia, Z.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

Xiao, Y.

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Xu, B.

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Xu, D.

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

Xu, E.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Xu, J.

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Xu, L.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Xu, X.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Yakunin, S.

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

Yan, D.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Yang, R. X.

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

Yang, Z.

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Yantara, N.

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

Yassitepe, E.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Ye, H.

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Yin, Y.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Yoon, Y. J.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Yu, S.

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Yu, W. W.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Yuan, M.

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Yuan, S.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

Zang, Z.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

C. Li, Z. Zang, W. Chen, Z. Hu, X. Tang, W. Hu, K. Sun, X. Liu, and W. Chen, “Highly pure green light emission of perovskite CsPbBr3 quantum dots and their application for green light-emitting diodes,” Opt. Express 24, 15071–15078 (2016).
[Crossref]

Zeng, H.

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

Zhang, C.

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

Zhang, F.

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

Zhang, J.

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Zhang, L.

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

Zhang, Q.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

Zhang, S.

J. Li, H. Dong, B. Xu, S. Zhang, Z. Cai, J. Wang, and L. Zhang, “CsPbBr3 perovskite quantum dots: saturable absorption properties and passively Q-switched visible lasers,” Photon. Res. 5, 457–460 (2017).
[Crossref]

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Zhang, T.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Zhang, X.

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Zhang, Y.

Y. Zhang, H. Zhu, T. Huang, Z. Song, and S. Ruan, “Radiation-pressure-induced photoluminescence enhancement of all-inorganic perovskite CsPbBr3 quantum dots,” Photon. Res. 7, 837–846 (2019).
[Crossref]

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Zhang, Z.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Zhao, C.

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Zhao, M.

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

Zhao, S.

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

Zhao, Y.

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Zheng, Y.

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

Zhong, G.

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Zhou, H.

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

Zhou, L.

Zhou, T.

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Zhu, H.

Zhuo, M.-P.

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

Zinna, J.

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

Zou, Y.

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

ACS Nano (2)

J. De Roo, M. Ibáñez, P. Geiregat, G. Nedelcu, W. Walravens, J. Maes, J. C. Martins, I. Van Driessche, M. V. Kovalenko, and Z. Hens, “Highly dynamic ligand binding and light absorption coefficient of cesium lead bromide perovskite nanocrystals,” ACS Nano 10, 2071–2081 (2016).
[Crossref]

S. Yuan, Z.-K. Wang, M.-P. Zhuo, Q.-S. Tian, Y. Jin, and L.-S. Liao, “Self-assembled high quality CsPbBr3 quantum dot films toward highly efficient light-emitting diodes,” ACS Nano 12, 9541–9548 (2018).
[Crossref]

ACS Photon. (1)

I. Dursun, C. Shen, M. R. Parida, J. Pan, S. P. Sarmah, D. Priante, N. Alyami, J. Liu, M. I. Saidaminov, M. S. Alias, A. L. Abdelhady, T. K. Ng, O. F. Mohammed, B. S. Ooi, and O. M. Bakr, “Perovskite nanocrystals as a color converter for visible light communication,” ACS Photon. 3, 1150–1156 (2016).
[Crossref]

ACS. Appl. Mater. Interface (1)

Y. Chang, Y. J. Yoon, G. Li, E. Xu, S. Yu, C.-H. Lu, Z. Wang, Y. He, C. H. Lin, B. K. Wagner, V. V. Tsukruk, Z. Kang, N. Thadhani, Y. Jiang, and Z. Lin, “All-inorganic perovskite nanocrystals with a stellar set of stabilities and their use in white light-emitting diodes,” ACS. Appl. Mater. Interface 10, 37267–37276 (2018).
[Crossref]

Adv. Funct. Mater. (4)

X. Zhang, B. Xu, J. Zhang, Y. Gao, Y. Zheng, K. Wang, and X. W. Sun, “All-inorganic perovskite nanocrystals for high-efficiency light emitting diodes: dual-phase CsPbBr3-CsPb2Br5 composites,” Adv. Funct. Mater. 26, 4595–4600 (2016).
[Crossref]

C. Wu, Y. Zou, T. Wu, M. Ban, V. Pecunia, Y. Han, Q. Liu, T. Song, S. Duhm, and B. Sun, “Improved performance and stability of all-inorganic perovskite light-emitting diodes by antisolvent vapor treatment,” Adv. Funct. Mater. 27, 1700338 (2017).
[Crossref]

B. T. Diroll, G. Nedelcu, M. V. Kovalenko, and R. D. Schaller, “High-temperature photoluminescence of CsPbX3 (X = Cl, Br, I) nanocrystals,” Adv. Funct. Mater. 27, 1606750 (2017).
[Crossref]

X. Li, Y. Wu, S. Zhang, B. Cai, Y. Gu, J. Song, and H. Zeng, “CsPbX3 quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes,” Adv. Funct. Mater. 26, 2435–2445 (2016).
[Crossref]

Adv. Mater. (4)

S. A. Veldhuis, P. P. Boix, N. Yantara, M. Li, T. C. Sum, N. Mathews, and S. G. Mhaisalkar, “Perovskite materials for light-emitting diodes and lasers,” Adv. Mater. 28, 6804–6834 (2016).
[Crossref]

J. Song, J. Li, X. Li, L. Xu, Y. Dong, and H. Zeng, “Quantum dot light-emitting diodes based on inorganic perovskite cesium lead halides (CsPbX3),” Adv. Mater. 27, 7162–7167 (2015).
[Crossref]

M. Zhao, H. Liao, L. Ning, Q. Zhang, Q. Liu, and Z. Xia, “Next-generation narrow-band green-emitting RbLi(Li3SiO4)2:Eu2+ phosphor for backlight display application,” Adv. Mater. 30, 1802489 (2018).
[Crossref]

J. Pan, L. N. Quan, Y. Zhao, W. Peng, B. Murali, S. P. Sarmah, M. Yuan, L. Sinatra, N. M. Alyami, J. Liu, E. Yassitepe, Z. Yang, O. Voznyy, R. Comin, M. N. Hedhili, O. F. Mohammed, Z. H. Lu, D. H. Kim, E. H. Sargent, and O. M. Bakr, “Highly efficient perovskite-quantum-dot light-emitting diodes by surface engineering,” Adv. Mater. 28, 8718–8725 (2016).
[Crossref]

Adv. Sci. (1)

M. Liu, G. Zhong, Y. Yin, J. Miao, K. Li, C. Wang, X. Xu, C. Shen, and H. Meng, “Aluminum-doped cesium lead bromide perovskite nanocrystals with stable blue photoluminescence used for display backlight,” Adv. Sci. 4, 1700335 (2017).
[Crossref]

Angew. Chem. Int. Ed. (2)

Y. Tong, E. Bladt, M. F. Aygüler, A. Manzi, K. Z. Milowska, V. A. Hintermayr, P. Docampo, S. Bals, A. S. Urban, L. Polavarapu, and J. Feldmann, “Highly luminescent cesium lead halide perovskite nanocrystals with tunable composition and thickness by ultrasonication,” Angew. Chem. Int. Ed. 55, 13887–13892 (2016).
[Crossref]

A. Swarnkar, R. Chulliyil, V. K. Ravi, M. Irfanullah, A. Chowdhury, and A. Nag, “Colloidal CsPbBr3 perovskite nanocrystals: luminescence beyond traditional quantum dots,” Angew. Chem. Int. Ed. 54, 15424–15428 (2015).
[Crossref]

Appl. Phys. Express (1)

S. Saito, R. Hashimoto, J. Hwang, and S. Nunoue, “InGaN light-emitting diodes ONC-face sapphire substrates in green gap spectral range,” Appl. Phys. Express 6, 111004 (2013).
[Crossref]

Appl. Phys. Lett. (1)

F. Nippert, S. Y. Karpov, G. Callsen, B. Galler, T. Kure, C. Nenstiel, M. R. Wagner, M. Straßburg, H.-J. Lugauer, and A. Hoffmann, “Temperature-dependent recombination coefficients in InGaN light-emitting diodes: hole localization, Auger processes, and the green gap,” Appl. Phys. Lett. 109, 161103 (2016).
[Crossref]

Dalton Trans. (1)

H. Zhou, Q. Wang, M. Jiang, X. Jiang, and Y. Jin, “A novel green-emitting phosphor Ba2Gd2Si4O13:Eu2+ for near UV-pumped light-emitting diodes,” Dalton Trans. 44, 13962–13968 (2015).
[Crossref]

J. Am. Chem. Soc. (2)

K. Wu, G. Liang, Q. Shang, Y. Ren, D. Kong, and T. Lian, “Ultrafast interfacial electron and hole transfer from CsPbBr3 perovskite quantum dots,” J. Am. Chem. Soc. 137, 12792–12795 (2015).
[Crossref]

M. C. Brennan, J. E. Herr, T. S. Nguyen-Beck, J. Zinna, S. Draguta, S. Rouvimov, J. Parkhill, and M. Kuno, “Origin of the size-dependent Stokes shift in CsPbBr3 perovskite nanocrystals,” J. Am. Chem. Soc. 139, 12201–12208 (2017).
[Crossref]

J. Display Technol. (1)

J. Mater. Chem. C (1)

Y. Xiao, Z. Hao, L. Zhang, X. Zhang, G.-H. Pan, H. Wu, H. Wu, Y. Luo, and J. Zhang, “An efficient green phosphor of Ce3+ and Tb3+-codoped Ba2Lu5B5O17 and a model for elucidating the high thermal stability of the green emission,” J. Mater. Chem. C 6, 5984–5991 (2018).
[Crossref]

J. Phys. Chem. C (1)

Y. Liu, J. Zhang, C. Zhang, J. Jiang, and H. Jiang, “High efficiency green phosphor Ba9Lu2Si6O24:Tb3+: visible quantum cutting via cross-relaxation energy transfers,” J. Phys. Chem. C 120, 2362–2370 (2016).
[Crossref]

J. Phys. Chem. Lett. (1)

J. Pan, S. P. Sarmah, B. Murali, I. Dursun, W. Peng, M. R. Parida, J. Liu, L. Sinatra, N. Alyami, C. Zhao, E. Alarousu, T. K. Ng, B. S. Ooi, O. M. Bakr, and O. F. Mohammed, “Air-stable surface-passivated perovskite quantum dots for ultra-robust, single- and two-photon-induced amplified spontaneous emission,” J. Phys. Chem. Lett. 6, 5027–5033 (2015).
[Crossref]

Jpn. J. Appl. Phys. (1)

S. Nakamura, M. Senoh, N. Iwasa, and S.-I. Nagahama, “High-brightness InGaN blue, green and yellow light-emitting diodes with quantum well structures,” Jpn. J. Appl. Phys. 34, L797-L799 (1995).
[Crossref]

Laser Photon. Rev. (1)

J. Cho, J. H. Park, J. K. Kim, and E. F. Schubert, “White light-emitting diodes: history, progress, and future,” Laser Photon. Rev. 11, 1600147 (2017).
[Crossref]

Light Sci. Appl. (1)

C. H. Kang, I. Dursun, G. Liu, L. Sinatra, X. Sun, M. Kong, J. Pan, P. Maity, E.-N. Ooi, T. K. Ng, O. F. Mohammed, O. M. Bakr, and B. S. Ooi, “High-speed colour-converting photodetector with all-inorganic CsPbBr3 perovskite nanocrystals for ultraviolet light communication,” Light Sci. Appl. 8, 94 (2019).
[Crossref]

Mater. Lett. (1)

D. Alexander, K. Thomas, S. Sisira, G. Vimal, K. P. Mani, P. R. Biju, N. V. Unnikrishnan, M. A. Ittyachen, and C. Joseph, “Photoluminescence properties of fully concentrated terbium oxalate: a novel efficient green emitting phosphor,” Mater. Lett. 189, 160–163 (2017).
[Crossref]

Mater. Sci. Eng. B (1)

Z. Yang, D. Xu, J. Sun, J. Du, and X. Gao, “Luminescence properties and energy transfer investigations of Sr3Lu(PO4)3:Ce3+, Tb3+ phosphors,” Mater. Sci. Eng. B 211, 13–19 (2016).
[Crossref]

Nano Energy (1)

H. Guan, S. Zhao, H. Wang, D. Yan, M. Wang, and Z. Zang, “Room temperature synthesis of stable single silica-coated CsPbBr3 quantum dots combining tunable red emission of Ag–In–Zn–S for high-CRI white light-emitting diodes,” Nano Energy 67, 104279 (2020).
[Crossref]

Nano Lett. (4)

G. Nedelcu, L. Protesescu, S. Yakunin, M. I. Bodnarchuk, M. J. Grotevent, and M. V. Kovalenko, “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, I),” Nano Lett. 15, 5635–5640 (2015).
[Crossref]

L. Protesescu, S. Yakunin, M. I. Bodnarchuk, F. Krieg, R. Caputo, C. H. Hendon, R. X. Yang, A. Walsh, and M. V. Kovalenko, “Nanocrystals of cesium lead halide perovskites (CsPbX3, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut,” Nano Lett. 15, 3692–3696 (2015).
[Crossref]

I. Lignos, L. Protesescu, D. B. Emiroglu, R. Maceiczyk, S. Schneider, M. V. Kovalenko, and A. J. deMello, “Unveiling the shape evolution and halide-ion-segregation in blue-emitting formamidinium lead halide perovskite nanocrystals using an automated microfluidic platform,” Nano Lett. 18, 1246–1252 (2018).
[Crossref]

I. Lignos, S. Stavrakis, G. Nedelcu, L. Protesescu, A. J. deMello, and M. V. Kovalenko, “Synthesis of cesium lead halide perovskite nanocrystals in a droplet-based microfluidic platform: fast parametric space mapping,” Nano Lett. 16, 1869–1877 (2016).
[Crossref]

Nano-Micro Lett. (1)

Z. Liu, B. Sun, X. Liu, J. Han, H. Ye, T. Shi, Z. Tang, and G. Liao, “Efficient carbon-based CsPbBr3 inorganic perovskite solar cells by using Cu-phthalocyanine as hole transport material,” Nano-Micro Lett. 10, 34 (2018).
[Crossref]

Nanomaterials (Basel) (1)

C. Chen, L. Zhang, T. Shi, G. Liao, and Z. Tang, “Controllable synthesis of all inorganic lead halide perovskite nanocrystals with various appearances in multiligand reaction system,” Nanomaterials (Basel) 9, 1751 (2019).
[Crossref]

Nanoscale (1)

H. Wu, Y. Zhang, M. Lu, X. Zhang, C. Sun, T. Zhang, V. L. Colvin, and W. W. Yu, “Surface ligand modification of cesium lead bromide nanocrystals for improved light-emitting performance,” Nanoscale 10, 4173–4178 (2018).
[Crossref]

Nanoscale Adv. (1)

L. Xu, J. Li, T. Fang, Y. Zhao, S. Yuan, Y. Dong, and J. Song, “Synthesis of stable and phase-adjustable CsPbBr3@Cs4PbBr6 nanocrystals via novel anion-cation reactions,” Nanoscale Adv. 1, 980–988 (2019).
[Crossref]

Nat. Commun. (1)

S. Yakunin, L. Protesescu, F. Krieg, M. I. Bodnarchuk, G. Nedelcu, M. Humer, G. De Luca, M. Fiebig, W. Heiss, and M. V. Kovalenko, “Low-threshold amplified spontaneous emission and lasing from colloidal nanocrystals of caesium lead halide perovskites,” Nat. Commun. 6, 8056 (2015).
[Crossref]

Nat. Mater. (1)

Z. Ning, O. Voznyy, J. Pan, S. Hoogland, V. Adinolfi, J. Xu, M. Li, A. R. Kirmani, J.-P. Sun, J. Minor, K. W. Kemp, H. Dong, L. Rollny, A. Labelle, G. Carey, B. Sutherland, I. Hill, A. Amassian, H. Liu, J. Tang, O. M. Bakr, and E. H. Sargent, “Air-stable n-type colloidal quantum dot solids,” Nat. Mater. 13, 822–828 (2014).
[Crossref]

Nat. Nanotechnology (1)

S. D. Stranks and H. J. Snaith, “Metal-halide perovskites for photovoltaic and light-emitting devices,” Nat. Nanotechnology 10, 391–402 (2015).
[Crossref]

Nat. Photonics (1)

B. R. Sutherland and E. H. Sargent, “Perovskite photonic sources,” Nat. Photonics 10, 295–302 (2016).
[Crossref]

Opt. Express (2)

Photon. Res. (2)

Phys. Status Solidi C (1)

T. Langer, A. Kruse, F. A. Ketzer, A. Schwiegel, L. Hoffmann, H. Jönen, H. Bremers, U. Rossow, and A. Hangleiter, “Origin of the green gap: increasing nonradiative recombination in indium-rich GaInN/GaN quantum well structures,” Phys. Status Solidi C 8, 2170–2172 (2011).
[Crossref]

Small (1)

D. Yan, T. Shi, Z. Zang, T. Zhou, Z. Liu, Z. Zhang, J. Du, Y. Leng, and X. Tang, “Ultrastable CsPbBr3 perovskite quantum dot and their enhanced amplified spontaneous emission by surface ligand modification,” Small 15, 1901173 (2019).
[Crossref]

Small Methods (1)

F. Zhang, J. Song, B. Han, T. Fang, J. Li, and H. Zeng, “High-efficiency pure-color inorganic halide perovskite emitters for ultrahigh-definition displays: progress for backlighting displays and electrically driven devices,” Small Methods 2, 1700382 (2018).
[Crossref]

Cited By

Optica participates in Crossref's Cited-By Linking service. Citing articles from Optica Publishing Group journals and other participating publishers are listed here.

Alert me when this article is cited.


Figures (5)

Fig. 1.
Fig. 1. (a) Schematic illustration of the surface in the CsPbBr3 QDs with ligand modification process, (b) XRD patterns, (c) FTIR spectra, and (d) HRTEM images for CsPbBr3 QDs.
Fig. 2.
Fig. 2. (a) PL spectra, (b) absorption spectra, and (c) lifetime of the CsPbBr3 QDs films. (d) XPS survey spectra of CsPbBr3 QDs. (e) Cs-3d spectrum, (f) Pb-4f spectrum, and (g) Br-3d spectrum. All peaks were calibrated using C 1s (284.8 eV).
Fig. 3.
Fig. 3. AFM images of the (a) CsPbBr3-OA and (b) CsPbBr3-DA QDs films.
Fig. 4.
Fig. 4. (a) and (b) Evolution of CsPbBr3 QDs coated on LED chips. The optical properties of (c)–(e) CsPbBr3-OA QDs and (f)–(h) CsPbBr3-DA QDs coated on LED chips. (c) and (f) Emission spectra, (d) and (g) green light purity analyses, and (e) and (h) behaviors of chromaticity coordinates with the addition of QDs solution.
Fig. 5.
Fig. 5. Optical properties of QDs coated on blue LEDs. (a) and (d) Spectrum intensity, (b) and (e) FWHM, and (c) and (f) behaviors of chromaticity coordinates under different injection currents.

Metrics