Abstract

We milled a sub-wavelength diffraction grating on the facet of a large mode area fiber. The diffraction grating had different reflectivities for TE and TM polarized light. It was tested in a thulium-doped fiber laser where it functioned as a low reflectivity output mirror integrated with an intracavity polarizer. Compared to the laser with a perpendicularly cleaved output fiber, the laser with diffraction grating had a slightly increased threshold power and the same slope efficiency. The beam quality factor M2 was not impaired. Polarization extinction ratios of about 20 dB that were observed at low laser powers dropped to 10 dB at high powers.

© 2016 Optical Society of America

1. Introduction

High-power polarized laser beams are needed in nonlinear optics to pump optical parametric oscillators [1, 2], generators of second harmonics [3], etc. In materials processing, the polarization dependence of laser cutting efficiency was discussed by Niziev and Nesterov [4]. Polarization-dependent, laser-induced periodic surface structures are formed on the laser-treated surfaces as a result of interference between the incident laser beam and surface scattered waves [5]. Polarization multiplexing is used to scale the power of fiber lasers [6].

Several approaches are used to achieve a stable and defined polarization state at the output of fiber lasers. Polarizing isolators, polarizers, and other hybrid elements are included into low-power fiber lasers made from polarization-maintaining (PM) fibers. The σ-laser configuration is used to mix PM and non-PM elements in resonators with defined output polarization [7].

Any passive intracavity element negatively influences the threshold, slope efficiency, reliability and cost of high-power fiber lasers. Active PM fibers were combined with a bulk polarization beam splitter in the resonator of a 300-watt ytterbium-doped fiber laser [8]. Cross-axis wavelength-matched fiber Bragg gratings were used to define the wavelength and linear polarization in a 100-watt ytterbium-doped fiber laser [9]. A linearly polarized output was achieved by inducing differential bending loss between the light polarized along the slow axis and fast axis of the PM fiber. Due to a lower effective index of refraction, light polarized along the fast axis of the fiber has higher bending loss when the fiber is wound into a coil of appropriate diameter. The technique was demonstrated for a 100-watt ytterbium-doped fiber laser [10].

One of the emerging technologies in fiber optics is the fabrication of microoptical elements directly on cleaved or polished end fiber facets through etching, milling or additive manufacturing. To date, interference lithography [11], photolithography [12], electron-beam lithography [13], focused ion-beam milling [14], nano-imprint technology [15,16], two-photon polymerization 3D printing [17–19], and laser micromachining were demonstrated as tools for fiber-facet patterning. The polymers are not yet suited for high-power applications and their exploitations is tricky due to polymerization inhomogeneities and nonuniform deformations occurring during the exposition and development processes [18]. The best suited technique of micro-patterning for high-power applications is etching or milling the microstructures directly on silica fiber facets.

In this paper, we present a polarizing diffraction grating etched directly on the fiber facet serving as a laser output reflector. We assume that light propagates in the fiber core towards the perpendicularly cleaved fiber end, which serves as a low-reflectivity mirror. The diffraction grating milled on the surface of the fiber facet modifies the reflection coefficient of the mirror. A focused ion beam was used to mill the grating grooves perpendicularly to the slow axis of the PM fiber. The grating parameters were optimized in a way ensuring that difference in reflections between the TE and TM modes was achieved, the reflection of the TE mode was close to optimum, and loss caused by diffraction into higher modes was low. The grating was tested in a thulium-doped fiber laser with a wavelength of 2040 nm at moderate powers.

Design and fabrication of diffraction gratings are described in Section 2 and 3, respectively. The grating performance in the laser at moderate powers is given in Section 4.

2. Diffraction grating design

The diffraction gratings properties were analyzed and optimized by means of a rigorous coupled-wave analysis (RCWA), finite-difference time-domain (FDTD) method, and Fourier modal method (FMM). The RSoft DiffractMOD, MIT MEEP [20], and UFE FMM [21] simulation software were used for RCWA, FDTD, and FMM analysis, respectively. The RCWA method allows fast optimization of grating parameters. The FDTD and FMM methods were used to evaluate the reflectivity of optimized gratings for guided mode, and the FDTD method additionally provided estimation of the modal loss.

Light diffraction is limited to zero order in sub-wavelength diffraction gratings. Optical properties of such gratings can be explained by the effective-medium theory [22]. The sub-wavelength grating behaves roughly as a homogeneous birefringent layer. Its reflectivity varies periodically with grating thickness with period depending on the polarization of incident light. The maximum reflectivity can not exceed a value given by Fresnel’s equations for an unstructured fiber facet in the effective-medium model.

Gratings with longer periods allow achieving zeroth order diffraction efficiencies beyond the Fresnel reflection limit at the expense of introducing loss due to the diffraction into higher reflected orders. In this work we optimized the grating with the aims as follows: a) achieving the reflectivity of the fundamental fiber mode close to the Fresnel reflection for unstructured fiber facet and avoiding diffraction into higher reflected modes in order to keep the laser threshold sufficiently low and slope efficiency high, b) designing the grating as shallow as possible to facilitate its fabrication, c) maximizing the difference between the grating reflectivity for TE and TM polarizations. The oscillation direction of electric field vector is parallel to the direction of grating grooves for TE polarization, and perpendicular for TM polarization. Our gratings were designed for a wavelength of 2040 nm. The product (R0TER0TM)R0TE, where R0TE and R0TM are zeroth order reflectivities for TE and TM polarized light, respectively, was adopted as a figure-of-merit (FOM).

The results of the RCWA optimization are shown in Fig. 1. The zeroth order reflectivity for TE-mode has oscillatory character as expected from the effective-medium model. The reflectivity is given by Fresnel’s equations for zero depth of the diffraction grating. The reflectivity decreases with increasing grating depth until the quarter depth is achieved. Almost complete suppression of the reflection is possible for appropriately chosen fill factor, which is approximately 0.3 for silica/air interface. Then the reflectivity grows again until the first maximum is achieved and the whole process repeats. The FOM closely follows oscillations of the zeroth order reflectivity with amplitude growing as a result of increasing difference in the zeroth order reflectivity of TE and TM modes. The FOM achieves its first maximum for a grating depth of 590 nm and fill factor of 0.6, and the second maximum at a grating depth of 1415 nm and fill factor of 0.55. The results of optimization are summarized in Table 1. The RCWA results were obtained for plane wave diffraction and were verified by 2D FDTD method for the diffraction of the guided mode of a slab waveguide with a thickness and numerical aperture matched to the fiber (Fig. 2). To complete the optimization, a 3D analysis of fundamental fiber mode reflection was performed by using FMM. Similar results are obtained by the FDTD and FMM methods, while the RCWA method allows interpretation of loss as a diffraction of light into ±1 orders. The ±1 reflected diffraction orders have angles that are far away beyond the total internal reflection angle of the weakly guiding core of single mode fiber and are source of loss. The FDTD simulations reveal a smoother onset of modal loss resulting from the onset of higher order diffraction in reflected light, as can be seen in Fig. 2b. The dashed curves in Fig 2b are obtained as a sum of diffraction efficiencies into the ±1 orders in reflection calculated by RCWA. Smoother onset results from low spectral resolution of the grating caused by low number of grooves irradiated by fiber mode. Further evidence of the source of loss is shown in Fig. 3, where ±1 orders are clearly visible in the diffraction pattern calculated by FDTD method.

 

Fig. 1 (a) Zeroth order reflectivity of the grating R0TE as a function of the grating depth and grating fill factor, and (b) figure-of-merit defined as the product (R0TER0TM)R0TE.

Download Full Size | PPT Slide | PDF

Tables Icon

Table 1. Parameters of optimized diffraction grating

 

Fig. 2 (a) Zero-order diffraction efficiency in reflection of TE and TM polarized light from diffraction grating numerically predicted by RCWA (dashed), FMM (dotted), and FDTD (solid) methods. (b) Loss by diffraction into higher orders predicted by RCWA technique (dashed) and modal loss predicted by FDTD method (solid).

Download Full Size | PPT Slide | PDF

 

Fig. 3 Ez component (parallel to grating grooves) of the field calculated by the FDTD method short after the reflection of the pulse propagating in the slab waveguide from the grating. The slab waveguide represents the fiber core in 2D simulations. The light pulse was emited from the fiber to right while the reflected pulse propagates in the fiber core to left and part of the incident pulse energy is lost in the cladding through diffraction into ±1 orders in reflection.

Download Full Size | PPT Slide | PDF

3. Fabrication of the diffraction grating

The designed grating was fabricated using the focused ion beam (FIB) milling. This single-step and maskless process is a very convenient technique for rapid prototyping. The milling was carried out using our FIB machine (Tescan LYRA3) with an ion source of liquid gallium, integrated with a scanning electron microscope (SEM), gas injection system (GIS), and secondary ion mass spectroscope (SIMS). The ion beam spot size of our FIB device for fine milling is about 70 nm. The limitations of our device are in the transversal dimensions of the structure 400 μm × 400 μm, the aspect ratio of the holes or trenches because the beam should be focused onto the bottom of the structure, and accumulation of the electric charge on the surface of the dielectric, which repels ions. In situ calibration was performed sufficiently far from the fiber core before inscribing the grating. A small-size test grating was milled close to the perimeter of the fiber, platinum strip was deposited across the grating grooves using GIS, and finally, a trench was etched to measure grating’s depth and fill factor. Based on the calibration data, a grating with dimensions of approximately 35 μm × 35 μm was fabricated centered at the fiber axis with grooves oriented along the fast axis of the PM fiber. The fiber facet with the diffraction and test gratings is shown in Fig. 4. The fabricated grating has a groove depth of approximately 550 nm and a fill factor of 0.7 which differs slightly from designed parameters. The difference from optimum parameters should have small effect on results as can be seen from Fig. 1.

 

Fig. 4 (a) Diffraction grating fabricated on the fiber facet. It is seen as a rectangle on backlit fiber core. The grating grooves are vertical. Stress elements of the PM fiber are seen as dark circles in the cladding. Test gratings are situated in the upper right part of the figure. (b) SEM image of the milled diffraction grating.

Download Full Size | PPT Slide | PDF

4. Test of the diffraction grating as a polarizer and output mirror in a fiber laser

The diffraction grating was tested in a thulium-doped fiber laser. The fiber laser only involves PM fibers and PM pigtailed optical components. The laser scheme is shown in Fig. 5. The resonator consists of an active fiber (PLMA-TDF), pump-signal combiner (PSC), and high-reflectivity fiber Bragg grating (HR-FBG). We used 35-watt 793-nanometer laser diodes from LIMO coupled to 220/280 μm multimode pigtails with a numerical aperture of 0.22 as pump sources. A double-clad thulium-doped PM fiber (PLMA-TDF-25P/400-HE from Nufern) with a large mode area and length of five meters was used as an active fiber. The fiber has a core diameter of 25 μm and an inner cladding diameter of 400 μm. It is coated with a low-index polymer with an outer diameter of 550 μm. The numerical apertures of the core and of the inner cladding are 0.09 and 0.46, respectively. The multimode pump absorption is 12 dB for a five-meters long fiber. The unabsorbed pump power is trapped in a cladding mode stripper (CMS). A laser resonator is created between the HR-FBG spliced to PSC and a low reflectivity mirror in the form of a perpendicularly cleaved output fiber. The HR-FBG has a reflectivity of 99.6% at a wavelength of 2039 nm and reflection bandwidth of 1 nm. The output mirror has a reflectivity of 3.5% given by Fresnel’s equations. The output laser power was measured with a power meter from Gentec. The polarization extinction ratio of the laser was determined using a Glan-Taylor polarizer and the beam quality factor was assessed by pyroelectric camera (Pyrocam III) combined with a linear kinematic stage. The optical spectrum was recorded by a Fourier transform infrared spectrometer (Nicolet 8700). The dependence of the laser output power on the launched pump power is shown in Fig. 6. The power launched into the active fiber was measured at the output of the pump-signal combiner as a function of pump laser diode currents during the construction of the laser before splicing with the active fiber. The laser has a maximum output power of 18 W, threshold of 7.4 W, and slope efficiency of 42%. The slope efficiency is lower than the slope efficiency of lasers pumped directly through the HR-FBG [23, 24], which we attribute to additional insertion loss of pump-signal combiner. We determined the M2 beam quality factor to be about 1.4, which indicates that higher-order modes are present in the large mode area fiber. The polarization extinction ratio of the laser beam was close to 1, which reflects the fact that no elements with significant polarization-dependent loss were included in the resonator.

 

Fig. 5 Thulium-doped fiber laser.

Download Full Size | PPT Slide | PDF

 

Fig. 6 (a) Dependence of the laser output power on the launched pump power for the perpendicularly cleaved fiber (blue) and fiber with difraction grating (red). (b) The maximum (red) and minimum (blue) power behind the external polarizer.

Download Full Size | PPT Slide | PDF

Once the fiber laser with a perpendicularly cleaved output fiber was characterized, we spliced the laser output fiber with the piece of the fiber where the diffraction grating was fabricated. We observed that the threshold slightly increased from 7.4 W to 9.9 W while the slope efficiency remained at 42% (Fig. 6a). This is in agreement with results of simulations where low diffraction loss is imposed by the grating, while the transmission coefficient of the grating is close to that of perpendicularly cleaved fiber. The measured polarization extinction ratio defined as PER = 10 log(Pmax/Pmin) was about 20 dB at low powers and decreased to 10 dB for the output power of 18 W (Fig. 7). The most probable reason of the PER degradation is excitation of the fast-axis mode in the laser and redistribution of the power between two existing modes because the reflectivity ratio between the TE and TM polarization of the grating is only slightly higher than 3dB. Higher extinction ratio could be expected for deeper output gratings with larger polarization selectivity operating in third or even higher FOM maximum (Fig. 1).

 

Fig. 7 Dependence of the laser output polarization extinction ratio on the launched pump power.

Download Full Size | PPT Slide | PDF

The minimum and maximum powers measured behind the polarizer are shown in Fig. 6b. The measured beam quality factor M2 measured at maximum power was 1.4, which is the same value obtained for the perpendicularly cleaved output fiber end. The measured beam diameter as a function of the camera position is shown in Fig. 8a) for both cases. The optical spectrum of the laser at maximum power is shown in Fig. 8b).

 

Fig. 8 (a) Dependence of the beam diameter on the camera position for the laser with a perpendicularly cleaved output fiber (blue) and with difraction grating (red). (b) The optical spectrum of the laser with diffraction grating.

Download Full Size | PPT Slide | PDF

5. Conclusion

Transmission properties of optical fibers can be modified by nanostructuring of the fiber end. In this paper, we modified the fiber facet reflection properties by milling a sub-wavelength diffraction grating on the facet of a perpendicularly cleaved fiber. The diffraction grating has different reflectivities for TE and TM polarized light and can act as a polarizer in a fiber laser. We tested the grating as an output low-reflection mirror in the moderate-power, thulium-doped fiber laser. The beam quality parameter M2 and slope efficiency were preserved while the laser threshold slightly increased. The output beam was polarized with a polarization extinction ratio of about 20 dB at low powers and 10 dB at high powers. No grating damage was observed up to 18 W of output power limited by experiment setup.

Funding

Czech Science Foundation, grant GAP15-07908S.

References and links

1. K. Devi, S. C. Kumar, and M. Ebrahim-Zadeh, “High-power, continuous-wave, single-frequency, all-periodically-poled, near-infrared source,” Opt. Lett. 37, 5049–5051 (2012). [CrossRef]   [PubMed]  

2. G. K. Samanta, S. C. Kumar, A. Aadhi, and M. Ebrahim-Zadeh, “Yb-fiber-laser-pumped, high-repetition-rate picosecond optical parametric oscillator tunable in the ultraviolet,” Opt. Express 22, 11476–11487 (2014). [CrossRef]   [PubMed]  

3. G. K. Samanta, S. C. Kumar, M. Mathew, C. Canalias, V. Pasiskevicius, F. Laurell, and M. Ebrahim-Zadeh, “High-power, continuous-wave, second-harmonic generation at 532 nm in periodically poled KTiOPO4,” Opt. Lett. 33, 2955–2957 (2008). [CrossRef]   [PubMed]  

4. V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999). [CrossRef]  

5. R. L. Harzic, D. Dörr, D. Sauer, M. Neumeier, M. Epple, H. Zimmermann, and F. Stracke, “Large-area, uniform, high-spatial-frequency ripples generated on silicon using a nanojoule-femtosecond laser at high repetition rate,” Opt. Lett. 36, 229–231 (2011). [CrossRef]   [PubMed]  

6. T. Y. Fan, “Laser beam combining for high-power, high-radiance sources,” IEEE Journal of Selected Topics in Quantum Electronics 11, 567–577 (2005). [CrossRef]  

7. P. Honzatko, P. Peterka, and J. Kanka, “Modulational-instability σ-resonator fiber laser,” Opt. Lett. 26, 810–812 (2001). [CrossRef]  

8. A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

9. J. Wang, J. Hu, L. Zhang, X. Gu, J. Chen, and Y. Feng, “A 100 W all-fiber linearly-polarized Yb-doped single-mode fiber laser at 1120 nm,” Opt. Express 20, 28373–28378 (2012). [CrossRef]   [PubMed]  

10. U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

11. X. Yang, N. Ileri, C. C. Larson, T. C. Carlson, J. A. Britten, A. S. P. Chang, C. Gu, and T. C. Bond, “Nanopillar array on a fiber facet for highly sensitive surface-enhanced raman scattering,” Opt. Express 20, 24819–24826 (2012). [CrossRef]   [PubMed]  

12. E. G. Johnson, J. Stack, T. J. Suleski, C. Koehler, and W. Delaney, “Fabrication of micro optics on coreless fiber segments,” Appl. Opt. 42, 785–791 (2003). [CrossRef]   [PubMed]  

13. M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering. [CrossRef]  

14. F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003. [CrossRef]  

15. G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008. [CrossRef]  

16. G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011). [CrossRef]   [PubMed]  

17. H. E. Williams, D. J. Freppon, S. M. Kuebler, R. C. Rumpf, and M. A. Melino, “Fabrication of three-dimensional micro-photonic structures on the tip of optical fibers using SU-8,” Opt. Express 19, 22910–22922 (2011). [CrossRef]   [PubMed]  

18. T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016). [CrossRef]   [PubMed]  

19. T. Gissibl, M. Schmid, and H. Giessen, “Spatial beam intensity shaping using phase masks on single-mode optical fibers fabricated by femtosecond direct laser writing,” Optica 3, 448–451 (2016). [CrossRef]  

20. A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010). [CrossRef]  

21. J. Čtyroký, “3-D bidirectional propagation algorithm based on fourier series,” J. Lightwave Technol. 30, 3699–3708 (2012). [CrossRef]  

22. P. Lalanne and J.-P. Hugonin, “High-order effective-medium theory of subwavelength gratings in classical mounting: application to volume holograms,” J. Opt. Soc. Am. A 15, 1843–1851 (1998). [CrossRef]  

23. P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013). [CrossRef]  

24. M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016). [CrossRef]  

References

  • View by:
  • |
  • |
  • |

  1. K. Devi, S. C. Kumar, and M. Ebrahim-Zadeh, “High-power, continuous-wave, single-frequency, all-periodically-poled, near-infrared source,” Opt. Lett. 37, 5049–5051 (2012).
    [Crossref] [PubMed]
  2. G. K. Samanta, S. C. Kumar, A. Aadhi, and M. Ebrahim-Zadeh, “Yb-fiber-laser-pumped, high-repetition-rate picosecond optical parametric oscillator tunable in the ultraviolet,” Opt. Express 22, 11476–11487 (2014).
    [Crossref] [PubMed]
  3. G. K. Samanta, S. C. Kumar, M. Mathew, C. Canalias, V. Pasiskevicius, F. Laurell, and M. Ebrahim-Zadeh, “High-power, continuous-wave, second-harmonic generation at 532 nm in periodically poled KTiOPO4,” Opt. Lett. 33, 2955–2957 (2008).
    [Crossref] [PubMed]
  4. V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999).
    [Crossref]
  5. R. L. Harzic, D. Dörr, D. Sauer, M. Neumeier, M. Epple, H. Zimmermann, and F. Stracke, “Large-area, uniform, high-spatial-frequency ripples generated on silicon using a nanojoule-femtosecond laser at high repetition rate,” Opt. Lett. 36, 229–231 (2011).
    [Crossref] [PubMed]
  6. T. Y. Fan, “Laser beam combining for high-power, high-radiance sources,” IEEE Journal of Selected Topics in Quantum Electronics 11, 567–577 (2005).
    [Crossref]
  7. P. Honzatko, P. Peterka, and J. Kanka, “Modulational-instability σ-resonator fiber laser,” Opt. Lett. 26, 810–812 (2001).
    [Crossref]
  8. A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.
  9. J. Wang, J. Hu, L. Zhang, X. Gu, J. Chen, and Y. Feng, “A 100 W all-fiber linearly-polarized Yb-doped single-mode fiber laser at 1120 nm,” Opt. Express 20, 28373–28378 (2012).
    [Crossref] [PubMed]
  10. U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.
  11. X. Yang, N. Ileri, C. C. Larson, T. C. Carlson, J. A. Britten, A. S. P. Chang, C. Gu, and T. C. Bond, “Nanopillar array on a fiber facet for highly sensitive surface-enhanced raman scattering,” Opt. Express 20, 24819–24826 (2012).
    [Crossref] [PubMed]
  12. E. G. Johnson, J. Stack, T. J. Suleski, C. Koehler, and W. Delaney, “Fabrication of micro optics on coreless fiber segments,” Appl. Opt. 42, 785–791 (2003).
    [Crossref] [PubMed]
  13. M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
    [Crossref]
  14. F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
    [Crossref]
  15. G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
    [Crossref]
  16. G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
    [Crossref] [PubMed]
  17. H. E. Williams, D. J. Freppon, S. M. Kuebler, R. C. Rumpf, and M. A. Melino, “Fabrication of three-dimensional micro-photonic structures on the tip of optical fibers using SU-8,” Opt. Express 19, 22910–22922 (2011).
    [Crossref] [PubMed]
  18. T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
    [Crossref] [PubMed]
  19. T. Gissibl, M. Schmid, and H. Giessen, “Spatial beam intensity shaping using phase masks on single-mode optical fibers fabricated by femtosecond direct laser writing,” Optica 3, 448–451 (2016).
    [Crossref]
  20. A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
    [Crossref]
  21. J. Čtyroký, “3-D bidirectional propagation algorithm based on fourier series,” J. Lightwave Technol. 30, 3699–3708 (2012).
    [Crossref]
  22. P. Lalanne and J.-P. Hugonin, “High-order effective-medium theory of subwavelength gratings in classical mounting: application to volume holograms,” J. Opt. Soc. Am. A 15, 1843–1851 (1998).
    [Crossref]
  23. P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
    [Crossref]
  24. M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
    [Crossref]

2016 (3)

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

T. Gissibl, M. Schmid, and H. Giessen, “Spatial beam intensity shaping using phase masks on single-mode optical fibers fabricated by femtosecond direct laser writing,” Optica 3, 448–451 (2016).
[Crossref]

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

2014 (1)

2013 (1)

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

2012 (4)

2011 (3)

2010 (1)

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

2009 (1)

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

2008 (1)

2005 (1)

T. Y. Fan, “Laser beam combining for high-power, high-radiance sources,” IEEE Journal of Selected Topics in Quantum Electronics 11, 567–577 (2005).
[Crossref]

2004 (1)

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

2003 (2)

E. G. Johnson, J. Stack, T. J. Suleski, C. Koehler, and W. Delaney, “Fabrication of micro optics on coreless fiber segments,” Appl. Opt. 42, 785–791 (2003).
[Crossref] [PubMed]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

2001 (1)

1999 (1)

V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999).
[Crossref]

1998 (1)

Aadhi, A.

Abrmczyk, J.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Austin, M.

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Baravets, Y.

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

Becker, M.

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

Bermel, P.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Bond, T. C.

Britten, J. A.

Brojek, W.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Businaro, L.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Cabrini, S.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Canalias, C.

Candeloro, P.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Carlson, T. C.

Carter, A.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Chang, A. S. P.

Chen, J.

Chinnasamy, U.

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

Cingolani, R.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Cojoc, D.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Ctyroký, J.

Degiorgio, V.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Delaney, W.

Devi, K.

Dörr, D.

Ebrahim-Zadeh, M.

Epple, M.

Fabrizio, E. D.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Fan, T. Y.

T. Y. Fan, “Laser beam combining for high-power, high-radiance sources,” IEEE Journal of Selected Topics in Quantum Electronics 11, 567–577 (2005).
[Crossref]

Farroni, J.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Feng, Y.

Freppon, D. J.

Gerardino, A.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Giessen, H.

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

T. Gissibl, M. Schmid, and H. Giessen, “Spatial beam intensity shaping using phase masks on single-mode optical fibers fabricated by femtosecond direct laser writing,” Optica 3, 448–451 (2016).
[Crossref]

Gigli, G.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Gissibl, T.

T. Gissibl, M. Schmid, and H. Giessen, “Spatial beam intensity shaping using phase masks on single-mode optical fibers fabricated by femtosecond direct laser writing,” Optica 3, 448–451 (2016).
[Crossref]

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

Gu, C.

Gu, X.

Guertin, D.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Harzic, R. L.

Herkommer, A.

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

Honzatko, P.

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

P. Honzatko, P. Peterka, and J. Kanka, “Modulational-instability σ-resonator fiber laser,” Opt. Lett. 26, 810–812 (2001).
[Crossref]

Hu, J.

Hugonin, J.-P.

Ibanescu, M.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Ileri, N.

Jacobson, N.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Jayawardhana, S.

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

Joannopoulos, J. D.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Johnson, E. G.

Johnson, S. G.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Kanka, J.

Khitrov, V.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Koehler, C.

Kostovski, G.

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Kuebler, S. M.

Kumar, R.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Kumar, S. C.

Lalanne, P.

Larson, C. C.

Laurell, F.

Liberale, C.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Liem, A.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Limpert, J.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Machewirth, D. P.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Mamajek, M.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Manyam, U. H.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Mathew, M.

Melino, M. A.

Michalska, M.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Mitchell, A.

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Nesterov, A. V.

V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999).
[Crossref]

Neumeier, M.

Niziev, V. G.

V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999).
[Crossref]

Oskooi, A. F.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Pasiskevicius, V.

Peterka, P.

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

P. Honzatko, P. Peterka, and J. Kanka, “Modulational-instability σ-resonator fiber laser,” Opt. Lett. 26, 810–812 (2001).
[Crossref]

Pisignano, D.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Prasciolu, M.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Reich, M.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Roundy, D.

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

Rumpf, R. C.

Rybak, Z.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Samanta, G. K.

Samson, B.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Sauer, D.

Schiappelli, F.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

Schmid, M.

Schreiber, T.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Stack, J.

Stoddart, P.

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Stoddart, P. R.

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

Stracke, F.

Suleski, T. J.

Swiderski, J.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Sznelewski, P.

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Tankala, K.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Thiele, S.

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

Todorov, F.

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

Tormen, M.

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

Tünnermann, A.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Visimberga, G.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

Vittorio, M. D.

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

Wang, J.

White, D.

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Williams, H. E.

Yang, X.

Zellmer, H.

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

Zhang, L.

Zimmermann, H.

Advanced Materials (1)

G. Kostovski, U. Chinnasamy, S. Jayawardhana, P. R. Stoddart, and A. Mitchell, “Sub-15nm optical fiber nanoimprint lithography: A parallel, self-aligned and portable approach,” Advanced Materials 23, 531–535 (2011).
[Crossref] [PubMed]

Appl. Opt. (1)

Biosensors and Bioelectronics (1)

G. Kostovski, D. White, A. Mitchell, M. Austin, and P. Stoddart, “Nanoimprinted optical fibres: Biotemplated nanostructures for SERS sensing,” Biosensors and Bioelectronics 24, 1531–1535 (2009). Selected Papers from the Tenth World Congress on Biosensors Shangai, China, May 14–16, 2008.
[Crossref]

Computer Physics Communications (1)

A. F. Oskooi, D. Roundy, M. Ibanescu, P. Bermel, J. D. Joannopoulos, and S. G. Johnson, “MEEP: A flexible free-software package for electromagnetic simulations by the FDTD method,” Computer Physics Communications 181, 687–702 (2010).
[Crossref]

IEEE Journal of Selected Topics in Quantum Electronics (1)

T. Y. Fan, “Laser beam combining for high-power, high-radiance sources,” IEEE Journal of Selected Topics in Quantum Electronics 11, 567–577 (2005).
[Crossref]

J. Lightwave Technol. (1)

J. Opt. Soc. Am. A (1)

Journal of Physics D: Applied Physics (1)

V. G. Niziev and A. V. Nesterov, “Influence of beam polarization on laser cutting efficiency,” Journal of Physics D: Applied Physics 32, 1455 (1999).
[Crossref]

Laser Physics Letters (2)

P. Honzatko, Y. Baravets, F. Todorov, P. Peterka, and M. Becker, “Coherently combined power of 20 W at 2000 nm from a pair of thulium-doped fiber lasers,” Laser Physics Letters 10, 095104 (2013).
[Crossref]

M. Michalska, W. Brojek, Z. Rybak, P. Sznelewski, M. Mamajek, and J. Swiderski, “Highly stable, efficient Tm-doped fiber laser – a potential scalpel for low invasive surgery,” Laser Physics Letters 13, 115101 (2016).
[Crossref]

Microelectronic Engineering (2)

M. Prasciolu, D. Cojoc, S. Cabrini, L. Businaro, P. Candeloro, M. Tormen, R. Kumar, C. Liberale, V. Degiorgio, A. Gerardino, G. Gigli, D. Pisignano, E. D. Fabrizio, and R. Cingolani, “Design and fabrication of on-fiber diffractive elements for fiber-waveguide coupling by means of e-beam lithography,” Microelectronic Engineering 67–68, 169–174 (2003). Proceedings of the 28th International Conference on Micro- and Nano-Engineering.
[Crossref]

F. Schiappelli, R. Kumar, M. Prasciolu, D. Cojoc, S. Cabrini, M. D. Vittorio, G. Visimberga, A. Gerardino, V. Degiorgio, and E. D. Fabrizio, “Efficient fiber-to-waveguide coupling by a lens on the end of the optical fiber fabricated by focused ion beam milling,” Microelectronic Engineering 73–74, 397–404 (2004). Micro and Nano Engineering 2003.
[Crossref]

Nature Communications (1)

T. Gissibl, S. Thiele, A. Herkommer, and H. Giessen, “Sub-micrometre accurate free-form optics by three-dimensional printing on single-mode fibres,” Nature Communications 7, 11763 (2016).
[Crossref] [PubMed]

Opt. Express (4)

Opt. Lett. (4)

Optica (1)

Other (2)

A. Liem, J. Limpert, T. Schreiber, M. Reich, H. Zellmer, A. Tünnermann, A. Carter, and K. Tankala, “High power linearly polarized fiber laser,” in “Conference on Lasers and Electro-Optics/International Quantum Electronics Conference and Photonic Applications Systems Technologies,” (Optical Society of America, 2004), p. CMS4.

U. H. Manyam, B. Samson, V. Khitrov, D. P. Machewirth, N. Jacobson, J. Farroni, D. Guertin, J. Abrmczyk, A. Carter, and K. Tankala, “Laser fibers designed for single polarization output,” in “Advanced Solid-State Photonics,” (Optical Society of America, 2004), p. MA6.

Cited By

OSA participates in Crossref's Cited-By Linking service. Citing articles from OSA journals and other participating publishers are listed here.

Alert me when this article is cited.


Figures (8)

Fig. 1
Fig. 1 (a) Zeroth order reflectivity of the grating R 0 TE as a function of the grating depth and grating fill factor, and (b) figure-of-merit defined as the product ( R 0 TE R 0 TM ) R 0 TE.
Fig. 2
Fig. 2 (a) Zero-order diffraction efficiency in reflection of TE and TM polarized light from diffraction grating numerically predicted by RCWA (dashed), FMM (dotted), and FDTD (solid) methods. (b) Loss by diffraction into higher orders predicted by RCWA technique (dashed) and modal loss predicted by FDTD method (solid).
Fig. 3
Fig. 3 Ez component (parallel to grating grooves) of the field calculated by the FDTD method short after the reflection of the pulse propagating in the slab waveguide from the grating. The slab waveguide represents the fiber core in 2D simulations. The light pulse was emited from the fiber to right while the reflected pulse propagates in the fiber core to left and part of the incident pulse energy is lost in the cladding through diffraction into ±1 orders in reflection.
Fig. 4
Fig. 4 (a) Diffraction grating fabricated on the fiber facet. It is seen as a rectangle on backlit fiber core. The grating grooves are vertical. Stress elements of the PM fiber are seen as dark circles in the cladding. Test gratings are situated in the upper right part of the figure. (b) SEM image of the milled diffraction grating.
Fig. 5
Fig. 5 Thulium-doped fiber laser.
Fig. 6
Fig. 6 (a) Dependence of the laser output power on the launched pump power for the perpendicularly cleaved fiber (blue) and fiber with difraction grating (red). (b) The maximum (red) and minimum (blue) power behind the external polarizer.
Fig. 7
Fig. 7 Dependence of the laser output polarization extinction ratio on the launched pump power.
Fig. 8
Fig. 8 (a) Dependence of the beam diameter on the camera position for the laser with a perpendicularly cleaved output fiber (blue) and with difraction grating (red). (b) The optical spectrum of the laser with diffraction grating.

Tables (1)

Tables Icon

Table 1 Parameters of optimized diffraction grating

Metrics