The impact of upper state lifetime and spatial hole burning on pulse shape and stability in actively mode locked QCLs is investigated by numerical simulations. It is shown that an extended upper state lifetime is necessary to achieve stable isolated pulse formation per roundtrip. Spatial hole burning helps to reduce the pulse duration by supporting broadband multimode lasing, but introduces pulse instabilities which eventually lead to strongly structured pulse shapes that further degrade with increased pumping. At high pumping levels gain saturation and recovery between pulses leads to suppression of mode locking. In the absence of spatial hole burning the laser approaches single-mode lasing, while in the presence of spatial hole burning the mode locking becomes unstable and the laser dynamics does not reach a steady state anymore.
© 2010 OSA
Short pulse generation from Quantum Cascade Lasers (QCLs) emitting in the mid-infrared region (3.5-20 μm) could serve many applications ranging from time-resolved spectroscopy [1,2], and nonlinear frequency conversion [3–5] to high-speed free space communication  and frequency metrology . QCLs  were first demonstrated in 1994 and they have become the most prominent and compact coherent light source in the mid-infrared. While conventional semiconductor lasers are bipolar devices and have an upper state lifetime ranging from hundreds of ps up to ns, QCLs are unipolar devices with an upper state lifetime that is in the few ps range. In QCLs, the emission wavelength, the gain spectrum and the carrier transport characteristics can be engineered over a wide range of values.
The gain bandwidth of QCLs is large enough to potentially generate sub-picosecond mid-infrared laser pulses due to the flexibility offered by band structure engineering. The most common technique for ultrashort pulse generation is mode locking, in which the longitudinal modes of the cavity are phaselocked either by an internal mechanism (passive mode locking) or by an external (active mode locking). However, short pulse generation from QCLs by mode locking is difficult due to the fast gain recovery time [9,10]. In intersubband transitions (i.e. transitions between quantized conduction band states in semiconductor quantum wells), the carrier relaxation time is very fast due to optical phonon scattering. As a result, the upper state lifetime in QCLs is typically one order of magnitude smaller than the roundtrip time, 40-60 ps, of typical few mm long laser structures [9,10]. Usually, this situation prevents the occurrence of mode locking, i.e. stable pulse formation. The reason is, that the gain fully recovers before the next pulse arrives or even immediately after the pulse if the gain is fast enough, which leads to less amplification of the peak of the pulse than its wings. Due to this process the pulse lengthens in time and the laser approaches continuous wave (cw) lasing. On the other hand, if the gain recovery time is longer than the cavity roundtrip time, the gain saturates with the average power in the laser cavity and does not shape the pulse significantly (Fig. 1 ). Therefore, most recently, QCLs with long upper state lifetime have been fabricated by implementing a “superdiagonal” gain structure. Upper state lifetimes of 50 ps, similar to the cavity roundtrip time, have been achieved. Using such structures, an actively mode-locked QCL [11,12] that produced stable and isolated picoseconds pulses, as confirmed by interferometric autocorrelation measurements, was demonstrated. Stable operation with these devices was obtained by current modulation of only a short section of the waveguide, while the whole waveguide was biased slightly above threshold.
In this work, first the impact of upper state lifetime and pumping level on pulse formation is discussed without taking spatial hole burning into account. Then the role of spatial hole burning (SHB) in pulse shaping, destabilization of mode locking and interaction with fast gain recovery and saturation is clarified, beyond what has been discussed previously in [12,13], by extensive numerical simulations. SHB significantly reduces the pulse duration by supporting broadband multimode operation. However, it leads to pulse instabilities and non stationary pulse generation from the laser.
2. Prior work on multimode regimes in QCLs
There are several previous works in which multimode regimes in QCLs were observed [6,14–16]. In  self mode locking of CW pumped QCLs was claimed. The lasers were emitting broadband optical spectra over a wide range of DC pumping levels. In the photocurrent spectrum a strong, stable and narrow (less than 100 kHz) peak was observed, which indicated long term coherence of phase relationships between the longitudinal modes. However, no autocorrelation data were reported from which one could infer the formation of a stable train of ultrashort pulses separated by the cavity roundtrip time.
In  active mode locking in QCLs, by modulating the laser current at the cavity roundtrip frequency, was pursued. Again, evidence of mode locking was deduced from the measured broadband optical spectra, as well as from the power spectra of the photocurrent. When the detuning between the driving frequency and the roundtrip frequency was large, only one mode was lasing. As the detuning was decreased more and more modes were lasing and a narrow beat note at roundtrip cavity frequency appeared. Information about the temporal profile of the generated pulses and proof for true short pulse generation can be obtained with second order autocorrelation measurements. Due to the lack of second order autocorrelators in the mid-infrared at that time, there was no direct evidence that the circulating waveform was consisting of a train of periodic isolated pulses with a stable steady state pulse shape.
Once autocorrelation techniques based on two photon absorption quantum well infrared photodetectors (QWIPs) [17,18] became available, it was discovered that the wideband multimode operation in QCLs is due to phenomena, such as spatial hole burning and the Risken-Nummedal-Graham-Haken (RNGH) instability [13,19]. Recently, it was proposed that self-induced transparency (SIT) together with a fast saturable absorber may be used to passively mode lock QCLs .
3. Device model and modulation scheme
The actively mode locked QCL, which we will study in the following is schematically depicted in Fig. 2a . A detailed description of a specific device can be found in . The laser cavity is formed by two semiconductor/air interfaces, which shall be located at z = 0 and z = L, where L is the cavity length. The cavity is divided into a short and a long section (Fig. 2b). Both sections are assumed to be equally and continuously pumped (DC pumping) with a current density, where denotes the threshold current density and the pump parameter p shows how many times the laser is pumped above threshold.
Active mode locking is achieved by sinusoidal modulation of the pump current injected into the short, electrically isolated, waveguide section with the roundtrip frequency of the passive cavity. The modulation is supposed to drive a large number of longitudinal modes above threshold by creating modulation sidebands resonant with neighboring modes. The pump current of the small section is then given by , where m is the modulation amplitude relative to threshold.
The modulation of the injection current into the short section leads to temporal variation of the roundtrip gain that a pulse can experience, favoring pulsed operation. The common approach to achieve active mode locking is by periodic modulation of the intracavity losses. Here, we modulate the gain. The short section of the cavity acts as a gain modulator, and the long section is pumped to transparency or to slight net gain, helping to compensate the other losses in the laser cavity.
4. Numerical model of QCL
4.1 Three-level versus two-level model
The dynamics of a QCL can be described by a three level model  as it is shown in Fig. 3a . It assumes that all QCL stages are identical and that laser action occurs between levels 2 and 1, the upper and lower states of the laser transition. Level 0 corresponds to the superlattice which connects to the next QCL stage, which is again described by the upper laser level 2. The current density J driven through the device by an external voltage acts as the pump current density from level 0 to level 2. is the lifetime of the upper level, is the lifetime of the lower laser level, that couples to the superlattice. In reality, there is also a superlattice transport time, , that describes the time it takes for the carriers to travel between different stages, which we neglect here. The rate equations for the 3-level system shown in Fig. 3a readsEq. (1)-(3)) which also does not involve this transport and this may be one reason for some of the remaining discrepancies between the theoretical and experimental results.
4.2 Maxwell-Bloch Equations
To describe the interaction of the laser field with the gain medium, we expand the two level rate equations to full Maxwell-Bloch Equations , that also take the coherent interaction between the field and the medium into account. The dynamics of polarization and inversion of the gain medium is described by the Bloch equations (Eq. (6-7)) and the pulse propagation through the gain medium located in the Fabry Perot cavity is described by the wave equation (Eq. (8)). The electric field propagates in both directions resulting in standing waves.Eq. (7) accounts for spatial diffusion of the inversion, i.e. of electrons in the upper laser level along the plane of the layers.
The waves traveling in the two directions are coupled as they share the same gain medium. This gives rise to SHB: the standing wave formed by a cavity mode imprints a grating in the gain medium through gain saturation. As a result, other modes may become more favorable for lasing and multimode operation is triggered.
We make the following ansatz for the electric field, the polarization and the inversion:Eq. (12-15)), but included in the simulation. In fact the low facet reflectivity is the major source of loss in this laser so that other small loss variations in the device due to changes in the operating conditions are expected to be of minor importance and can be safely neglected. In contrast to ref , we do not include any effective saturable absorber effects due to potential Kerr-Lensing, since we compare the simulations later with experimental results from devices with a wide ridge (8-20μm), where such effects are greatly reduced as discussed in .
For simulation purposes, i.e. elimination of noncritical model parameters, we normalize the field with respect to the dipole matrix element, i.e. Rabi frequency, and correspondingly polarization, inversion, inversion grating and pumping as follows:Eq. (16). Thus for the forward propagating field we findEq. (18) for the inversion and since there is no grating, = 0. We therefore find that the small signal gain is given by . At threshold the gain is equal to the losses, thus the pumping at threshold must beand the inversion at threshold is . For the following, we normalize the plots for the inversion always with respect to the threshold inversion for ease of interpretation.
Spatial hole burning is associated with the amplitude of the inversion grating that couples the electric fields propagating along the two directions in the laser. As can be seen from Eq. (19) the inverse lifetime of the gain grating is given by , i.e. it is the sum of the terms due to diffusion of the carrier density modulation and the inverse carrier lifetime, since the latter is the rate by which carriers are homogenously injected in each volume element. SHB is strong in mid-IR QCLs since the strength of diffusion, which combats the carrier density modulation, scales with the square of the wave number k , which is about an order of magnitude smaller for mid-IR QCLs than for semiconductor lasers in the visible. In steady state, Eq. (18) shows that the term that drives the inversion grating in Eq. (19) scales with . So, in steady state, the strength of the carrier density modulation or gain grating is. In AlInAs-InGaAs heterostructures, the diffusion coefficient D is 46 cm2/sec at 77 K and for vacuum wavelength 6.2 μm, we obtain 4k2D = 0.2 THz. In regular mid-IR QCLs (T1 = 5 ps), is roughly the same as 1/ T1 and SHB is strong (). Even for a longer upper state lifetime, such as T1 = 50 ps, which is the case for the “superdiagonal” QCL structures discussed here, the effects of SHB cannot be neglected (). Due to the fast gain recovery time of QCLs, carrier diffusion cannot suppress SHB, in contrast to standard semiconductor lasers.
5. QCL Dynamics
In this section we show and discuss the simulation results, initially without and then with SHB. The parameters that stay fixed and are used in all examples in this paper, if not otherwise explicitly noted, are given in Table 1 . It is important to note, that for the QCL with superdiagonal gain structure discussed here, the roundtrip time is almost equal to the gain recovery time, T1, a fact that enables stable mode locking as explained before.
5.1 QCL Dynamics without SHB
First, the steady state behavior of the laser is investigated when SHB is not included in the Maxwell-Bloch equations (i.e. ). Initially the continuous wave steady state solution of the model is determined when the current modulation is switched off. Figure 4 shows the resulting total intracavity intensity and normalized inversion. That means, in each point of the cavity there is a forward and a backward wave and we add the intensities of both waves to the total intensity at each point. The total intensity increases slightly towards the facets of the cavity to compensate for the output coupling losses and as a result the gain is more strongly saturated at the edges than in the center of the cavity.
For completeness, Fig. 5 shows the pumping, the inversion and the intensity versus time for a point inside the short (modulated) section. The inversion does not follow the pumping current instantaneously, because the modulation frequency is close to the inverse gain recovery time (i.e = 17.86 GHz and GHz) and as a result the inversion is delayed by almost 90 degrees compared to the pumping. Also, the gain peak does not coincide with the pulse maximum. The front of the pulse extracts gain so it is more amplified than the back of the pulse experiencing the reduced gain, due to the long gain recovery time compared to the pulse duration. As a result, the group velocity of the pulse is increased.
Second the laser dynamics under current modulation is studied. Figure 6 shows the intensity of the output pulses from the QCL at the right end of the laser cavity, (i.e. the laser output is monitored as a function of time) for different DC pumping levels and constant modulation amplitude (m = 5). As expected, isolated pulses with a steady state pulse shape are formed by the strong gain modulation in the short gain section. For increased DC-pumping levels of the long gain section, the pulse energy or average output power is increasing. The pulse duration depends on the pumping level. This can be understood by the fact that the long section acts as an amplifier with a recovery time on the order of the cavity roundtrip time. Although the gain is slow, with a recovery time equal the cavity roundtrip time, it leads to substantial reshaping of the pulse towards longer pulses, i.e. suppression of multimode operation. When the DC pumping level is close to threshold (p = 1.1) the pulse is weak and therefore only weakly saturates the amplifier leading to minimum pulse lengthening during propagation through the long section. The long section mostly helps to compensate for the waveguide and facet losses. With increasing DC pumping (p = 1.45 and p = 1.61), the pulse energy and with it the gain saturation and pulse lengthening increases, explaining the increase in pulse duration with increased pumping.
For the purpose of comparison with later simulation and experimental results, Fig. 7 shows the normalized spectral intensities and Fig. 8 shows the computed Interferometric Autocorrelation (IAC) traces for the three cases in Figs. 6a-6c. When DC pumping is close to threshold many modes are lasing and locked (Fig. 7a) and as a result the pulses are fairly short, as we can see in Fig. 6a. As DC pumping increases we can see in Fig. 6 that the pulses become longer in time and from the spectra we observe that fewer modes are lasing due to the intensity smoothing effect of a saturating and fast recovering gain in the long section. For low DC pumping level the ratio of peak to background is 8:1 (Fig. 8a), which verifies that the pulses are isolated. IAC traces for higher DC pumping levels start to overlap. For the case without SHB, the IAC traces and in fact the computed electric fields do not show any chirp i.e. nontrivial phase over the pulse.
As we will see later, these do not fully account for what is found experimentally and inclusion of SHB is necessary to explain the observations.
5.2 Experimental observations
The experiments are described in detail in . The experimental results show the same general trend of pulse lengthening with increased DC pumping, however there is a major difference. The pulses in the simulations are in general longer in time than the pulses observed experimentally. For the case of a DC pumping parameter p = 1.1, the pulse in Fig. 6a is close to a Gaussian with a 7 ps FWHM duration. The measured interferometric autocorrelations for different pumping levels are shown in Fig. 9 , and in particular for p = 1.1 in Fig. 9a, assuming a Gaussian pulse shape, a FWHM pulse duration of 3 ps is extracted. The experimentally observed spectra are also much more broadband compared to the theoretical ones from the simulation. This indicates that SHB is important and must be incorporated in the model.
5.3 QCL Dynamics with SHB
To include SHB in the model we use Eqs. (16-19) in the simulations. The total inversion now consists of the average inversion Δ0 and the inversion grating. The interference of the two counter-propagating waves produces a standing wave pattern in the optical intensity, which in turn varies spatially the saturation of the laser medium. Due to the spatial gain grating more modes start lasing, however as we will show below this grating does not become stationary. The wave, as it propagates, is reflected from the nonstationary grating at some positions (SHB interferes with mode locking) and this leads to differential and time varying phase shifts between the modes. Thus, in the presence of SHB the modes acquire nonlinear phase shifts and with it also the pulse. Like in the case without SHB, the DC pumping level should be close to threshold so that the pulses do not lengthen too much.
To obtain insight into the nonstationary gain grating, the continuous wave solution of the model is determined in the absence of a current modulation. In Fig. 10 we show the inversion along the cavity for DC pumping 1.1 times above threshold at three different times about 5000 roundtrips apart. As the number of roundtrips increases, the average inversion and the inversion grating continue to evolve and never reach a steady state. The inversion profile and inversion grating show a degree of randomness. If there would be a steady state, one would expect that due to the large losses per roundtrip the system would certainly come into steady state within at least a hundred roundtrips. This is not the case.
If we increase the DC pumping to 2 times above threshold, the degree of randomness in the grating is further increased due to the increase in the number of modes that are lasing, see Fig. 11 .
In the following, we show the intensity and the inversion profiles in the cavity when the modulation is switched on, for various time instants and different DC pumping levels. In Fig. 12 the DC pumping is 1.1 times above threshold. When the pulse is reflected from one of the facets, Figs. 12a and 12c, a grating is formed due to the presence of forward and backward waves. Since there are isolated pulses produced, there is no grating when the pulse is propagating in the middle of the cavity, Fig. 12b. However, there is still some gain grating left over at the left end of the waveguide, where the pulse was reflected last and consequently the grating has not yet decayed completely.
If we increase the DC pumping to 2 times above threshold (Fig. 13 ) there are no longer isolated pulses per roundtrip. The pulse has broken up into multiple beats of the lasing modes, due to the large and too fast recovering gain in the long waveguide section and a gain grating is observable over the full length of the laser cavity.
Similar to Figs. (6-8), we simulate the laser dynamics under current modulation in the presence of SHB. The simulation results shown in the following are snapshots of the laser dynamics after simulating 10,750 roundtrips (0.6 μs). Figure 14 shows the normalized time averaged spectral intensities that are generated by Fourier-Transformation of a 29 roundtrip long time series, and Fig. 15 shows the intensity of the output pulses at the end of the QCL cavity for different DC pumping levels and constant modulation amplitude (m = 5) for a duration of about three cavity roundtrips. As explained above, the generated pulse trains and spectra do not reach a true steady state, but rather remain dynamic on the few percent level. If we compare the spectral intensities in Fig. 14 with the ones in Fig. 7, where no SHB is included, we see that many more modes are lasing in the presence of SHB in agreement with the experiment. For DC pumping close to threshold (p = 1.1) the phases between the modes are locked to the values favoring the formation of an isolated pulse and the main peak of the pulse becomes as short as 2 ps (Fig. 15a). With increasing DC pumping level, more modes start lasing (Figs. 14b, 14c), since the magnitude of the inversion grating becomes stronger. At the same time, the intensity profile of the pulses becomes more structured (Figs. 15b, 15c). The reason for the structure is the decorrelation of the phases between the modes due to SHB. Also the speed of the gain modulation, which stays fixed, is no longer capable to lock all modes of the increasingly broadband spectrum. Furthermore, with increased DC-pumping, passive gain modulation in the amplifier section, due to gain saturation by the pulse and partial gain recovery, becomes stronger and again the peak of the pulse experiences less gain than the wings, destabilizing short pulse generation.
The computed IAC traces for the three cases in Fig. 15 are shown in Fig. 16 and reflect the structure that is observed in the intensity profiles. As DC pumping increases, we observe in the IAC traces more and more substructure. The simulation traces back this sub-structure to the nonlinear phase introduced by SHB.
The grating decay time Tg is always smaller than the upper state lifetime T1, see Eq. (19). When the effects of carrier diffusion are negligible, i.e. Tg becomes close to T1, the strength of SHB increases (the amplitude of the inversion grating relaxes slower) and the side lobes in the IAC become more pronounced. In Fig. 17a we see the effect on the side lobes when Tg increases from 5 ps (used so far) to 10 ps. The same behavior also occurs when T1 decreases. As explained before, decrease in T1 results in increase of the effect of SHB and subsequent deterioration of the pulse quality as it is shown in Fig. 17b.
We have shown by numerical simulations the limitations in achieving stable short pulse generation from actively mode-locked QCLs, due to the limited upper state lifetime and spatial hole burning. A stable regime of modelocking only occurs for carefully adjusted DC pumping level close to threshold and strong modulation of the pump current in a short modulator section. SHB helps to reduce the pulse duration, but deteriorates pulse quality. Further increase in DC pumping results in pulse lengthening and deterioration of pulse quality both due to spatial hole burning and increased gain modulation due to gain saturation by the pulse and subsequent partial gain recovery. Simulations and experimental results show the same trend as DC pumping increases.
This research was supported in part by the United States Air Force Office of Scientific Research (AFOSR) grant FA9550-07-1-0014. V.-M. Gkortsas acknowledges support from Alexander S. Onassis Public Benefit Foundation.
References and links
1. R. Huber, F. Tauser, A. Brodschelm, M. Bichler, G. Abstreiter, and A. Leitenstorfer, “How many-particle interactions develop after ultrafast excitation of an electron-hole plasma,” Nature 414(6861), 286–289 (2001). [CrossRef] [PubMed]
3. J. M. Dudley, G. Genty, and S. Coen, “Supercontinuum generation in photonic crystal fiber,” Rev. Mod. Phys. 78(4), 1135–1184 (2006). [CrossRef]
5. E. A. Gibson, A. Paul, N. Wagner, R. Tobey, D. Gaudiosi, S. Backus, I. P. Christov, A. Aquila, E. M. Gullikson, D. T. Attwood, M. M. Murnane, and H. C. Kapteyn, “Coherent soft x-ray generation in the water window with quasi-phase matching,” Science 302(5642), 95–98 (2003). [CrossRef] [PubMed]
6. R. Paiella, F. Capasso, C. Gmachl, H. Hwang, D. Sivco, A. Hutchinson, A. Y. Cho, and H. C. Liu, “Monolithic active mode locking of quantum cascade lasers,” Appl. Phys. Lett. 77(2), 169–171 (2000). [CrossRef]
9. H. Choi, L. Diehl, Z.-K. Wu, M. Giovannini, J. Faist, F. Capasso, and T. B. Norris, “Gain recovery dynamics and photon-driven transport in quantum cascade lasers,” Phys. Rev. Lett. 100(16), 167401 (2008). [CrossRef] [PubMed]
10. H. Choi, T. B. Norris, T. Gresch, M. Giovannini, J. Faist, L. Diehl, and F. Capasso, “Femtosecond dynamics of resonant tunneling and superlattice relaxation in quantum cascade lasers,” Appl. Phys. Lett. 92(12), 122114–122117 (2008). [CrossRef]
11. C. Wang, L. Kuznetsova, L. Diehl, F. Kaertner, M. Belkin, H. Schneider, H. C. Liu, and F. Capasso, “Stable Mode-locked pulses from Mid-Infrared Quantum Cascade Lasers,” Postdeadline paper, Conference of Lasers and Electro optics, San Jose, CA, USA, 2008.
12. C. Y. Wang, L. Kuznetsova, V. M. Gkortsas, L. Diehl, F. X. Kärtner, M. A. Belkin, A. Belyanin, X. Li, D. Ham, H. Schneider, P. Grant, C. Y. Song, S. Haffouz, Z. R. Wasilewski, H. C. Liu, and F. Capasso, “Mode-locked pulses from mid-infrared quantum cascade lasers,” Opt. Express 17(15), 12929–12943 (2009). [CrossRef] [PubMed]
13. A. Gordon, C. Wang, L. Diehl, F. Kaertner, A. Belyanin, D. Bour, S. Corzine, G. Hoefler, H. C. Liu, H. Schneider, T. Maier, M. Trocolli, J. Faist, and F. Capasso, “Multimode regimes in quantum cascade lasers: From coherent instabilities to spatial hole burning,” Phys. Rev. A 77(5), 053804 (2008). [CrossRef]
14. R. Paiella, F. Capasso, C. Gmachl, D. L. Sivco, J. N. Baillargeon, A. L. Hutchinson, A. Y. Cho, and H. C. Liu, “Self-mode-locking of quantum cascade lasers with giant ultrafast optical nonlinearities,” Science 290(5497), 1739–1742 (2000). [CrossRef] [PubMed]
15. A. Soibel, F. Capasso, C. Gmachl, M. Peabody, A. M. Sergent, R. Paiella, D. Sivco, A. Y. Cho, H. C. Liu, A. Y. Cho, and H. C. Liu, “Stability of Pulse Emission and Enhancement of Intracavity Second-Harmonic Generation in Self-Mode-Locked Quantum Cascade Lasers,” IEEE J. Quantum Electron. 40(3), 197–204 (2004). [CrossRef]
16. A. Soibel, F. Capasso, C. Gmachl, M. Peabody, A. M. Sergent, R. Paiella, H. Hwang, D. Sivco, A. Y. Cho, H. C. Liu, C. Jirauschek, and F. X. Kartner, “Active Mode locking of Broadband quantum Cascade Lasers,” IEEE J. Quantum Electron. 40(7), 844–851 (2004). [CrossRef]
17. H. C. Liu and E. Dupont, “Nonlinear quantum well infrared photodetector,” J. Nonlinear Opt. Phys. Mater. 11(4), 433–443 (2002). [CrossRef]
18. T. Maier, H. Schneider, H. C. Liu, M. Walther, and P. Koidl, “Two-photon QWIPs for quadratic detection of weak mid-infrared laser pulses,” Infrared Phys. Technol. 47(1-2), 182–187 (2005). [CrossRef]
19. C. Y. Wang, L. Diehl, A. Gordon, C. Jirauschek, F. X. Kartner, A. Belyanin, D. Bour, S. Corzine, G. Hoefler, M. Troccoli, J. Faist, and F. Capasso, “Coherent instabilities in a semiconductor laser with fast gain recovery,” Phys. Rev. A 75(3), 031802 (2007). [CrossRef]
21. J. Faist, D. Hofstetter, M. Beck, T. Aellen, M. Rochat, and S. Blaser, “Bound-to-continuum and tow-phonon resonance quantum cascade lasers for high duty cycle, high temperature operation,” IEEE J. Quantum Electron. 38(6), 533–546 (2002). [CrossRef]