Abstract

The spatio-temporal evolution of the temperature induced over carbon fiber reinforced polymer (CFRP) laminates during drilling is monitored in real-time using a distributed optical fiber sensor based on optical frequency-domain reflectometry (OFDR). The proposed distributed measurement technique enables the simultaneous monitoring of thousands independent points on a CFRP plate during machining, being of special interest to measure the internal temperature of a workpiece. Experimental results validate the use of distributed OFDR-based sensing for this novel application, demonstrating a precise reconstruction of the two-dimensional (2D) temperature profile around the drilled hole, with a 2 mm spatial resolution and a sampling rate of 23.8 Hz (corresponding to a measurement interval of 42 ms). The high spatial and temporal resolutions provided by OFDR sensing offer unique features for this application, allowing for an accurate identification of the temporal evolution and spatial distribution of the 2D temperature profile originated during drilling. By embedding the sensing optical fiber in the interface between CFRP laminates and metals, a full map of the internal (interlayer) temperature of the CFRP plate can be obtained, demonstrating a feature that cannot be obtained by any other sensing technology. The proposed method can constitute a relevant tool for the identification of potential high temperatures occurring during machining, which could affect the quality of the borehole, induce material defects, and compromise the safety of an entire composite structure in service.

PDF Article

References

  • View by:
  • |
  • |
  • |

  1. M. A. Karataş and H. Gökkaya, “A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials,” Defence Technol., vol. 14, no. 4, pp. 318–326, 2018.
  2. C. Soutis, “Fibre reinforced composites in aircraft construction,” Prog. Aerosp. Sci., vol. 41, no. 2, pp. 143–151, 2005.
  3. A. Pramaniket al., “Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys—A review,” Compos. Part A, Appl. Sci. Manuf., vol. 101, pp. 1–29, 2017.
  4. R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.
  5. R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.
  6. A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.
  7. O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.
  8. J. Xu and M. E. Mansori, “Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite,” Int. J. Adv. Manuf. Technol., vol. 87, pp. 657–675, 2016.
  9. K. Weinert and C. Kempmann, “Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites,” Adv. Eng. Mater., vol. 6, pp. 684–689, 2004.
  10. F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.
  11. J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.
  12. R. Fuet al., “Drill-exit temperature characteristics in drilling of UD and MDCFRP composites based on infrared thermography,” Int. J. Mach. Tools Manuf., vol. 135, pp. 24–37, 2018.
  13. J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.
  14. S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.
  15. C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.
  16. M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .
  17. Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.
  18. A. D. Kerseyet al., “Fiber grating sensors,” J. Lightw. Technol., vol. 15, no. 8, pp. 1442–1463, 1997.
  19. Y. J. Rao, “In-fibre Bragg grating sensors,” Meas. Sci. Technol., vol. 8, no. 4, 1997, Art. no. .
  20. N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.
  21. C. G. Askins, M. A. Putnam, G. M. Williams, and E. J. Friebele, “Stepped-wavelength optical-fiber Bragg grating arrays fabricated in line on a draw tower,” Opt. Lett., vol. 19, no. 2, pp. 147–149, 1994.
  22. M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.
  23. A. Hartog, An Introduction to Distributed Optical Fibre Sensors. Boca Raton, FL, USA: CRC Press, 2017.
  24. P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.
  25. P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.
  26. W. Eickhoff and R. Ulrich, “Optical frequency domain reflectometry in single‐mode fiber,” Appl. Phys. Lett., vol. 39, no. 9, pp. 693–695, 1981.
  27. Z. Dinget al., “Distributed optical fiber sensors based on optical frequency domain reflectometry: A review,” Sensors, vol. 18, no. 4, 2018, Art. no. .
  28. X. Fan, “Distributed Rayleigh sensing,” in Handbook of Optical Fibers, G. D. Peng, Ed. Singapore: Springer, 2018.
  29. L. Palmieri and L. Schenato, “Distributed optical fiber sensing based on Rayleigh scattering,” Open Opt. J., vol. 7, no. 1, pp. 104–127, 2013.
  30. W. Hintze, C. Schutte, and S. Steinbach, “Influence of the fiber cutting angle on work piece temperature in drilling of unidirectional CFRP,” in New Production Technologies in Aerospace Industry, B. Denkena, Ed.New York, NY, USA: Springer, 2013.
  31. Z. Jianshe, “Measuring and analyzing of drilling temperature for carbon fiber reinforced composites,” Aerosp. Mater. Technol., no. 5, pp. 49–52, 2000.
  32. Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.
  33. S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

2018 (5)

M. A. Karataş and H. Gökkaya, “A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials,” Defence Technol., vol. 14, no. 4, pp. 318–326, 2018.

R. Fuet al., “Drill-exit temperature characteristics in drilling of UD and MDCFRP composites based on infrared thermography,” Int. J. Mach. Tools Manuf., vol. 135, pp. 24–37, 2018.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Z. Dinget al., “Distributed optical fiber sensors based on optical frequency domain reflectometry: A review,” Sensors, vol. 18, no. 4, 2018, Art. no. .

2017 (1)

A. Pramaniket al., “Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys—A review,” Compos. Part A, Appl. Sci. Manuf., vol. 101, pp. 1–29, 2017.

2016 (4)

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

J. Xu and M. E. Mansori, “Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite,” Int. J. Adv. Manuf. Technol., vol. 87, pp. 657–675, 2016.

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

2015 (3)

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

2014 (2)

S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

2013 (2)

A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.

L. Palmieri and L. Schenato, “Distributed optical fiber sensing based on Rayleigh scattering,” Open Opt. J., vol. 7, no. 1, pp. 104–127, 2013.

2011 (1)

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

2010 (1)

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.

2005 (1)

C. Soutis, “Fibre reinforced composites in aircraft construction,” Prog. Aerosp. Sci., vol. 41, no. 2, pp. 143–151, 2005.

2004 (1)

K. Weinert and C. Kempmann, “Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites,” Adv. Eng. Mater., vol. 6, pp. 684–689, 2004.

2002 (1)

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

2000 (1)

Z. Jianshe, “Measuring and analyzing of drilling temperature for carbon fiber reinforced composites,” Aerosp. Mater. Technol., no. 5, pp. 49–52, 2000.

1997 (2)

A. D. Kerseyet al., “Fiber grating sensors,” J. Lightw. Technol., vol. 15, no. 8, pp. 1442–1463, 1997.

Y. J. Rao, “In-fibre Bragg grating sensors,” Meas. Sci. Technol., vol. 8, no. 4, 1997, Art. no. .

1994 (1)

1981 (1)

W. Eickhoff and R. Ulrich, “Optical frequency domain reflectometry in single‐mode fiber,” Appl. Phys. Lett., vol. 39, no. 9, pp. 693–695, 1981.

An, Q.

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

Ashrafi, S. A.

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

Askins, C. G.

Ayvar-Soberanis, S.

J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.

Bergheau, J.

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

Bukkapatnam, S. T. S.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Cai, X.

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

Chegdani, F.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Chen, M.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

Collombet, F.

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.

Ding, Z.

Z. Dinget al., “Distributed optical fiber sensors based on optical frequency domain reflectometry: A review,” Sensors, vol. 18, no. 4, 2018, Art. no. .

Drapier, S.

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

Eickhoff, W.

W. Eickhoff and R. Ulrich, “Optical frequency domain reflectometry in single‐mode fiber,” Appl. Phys. Lett., vol. 39, no. 9, pp. 693–695, 1981.

Fan, X.

X. Fan, “Distributed Rayleigh sensing,” in Handbook of Optical Fibers, G. D. Peng, Ed. Singapore: Springer, 2018.

M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.

Farrell, G.

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

Friebele, E. J.

Fu, R.

R. Fuet al., “Drill-exit temperature characteristics in drilling of UD and MDCFRP composites based on infrared thermography,” Int. J. Mach. Tools Manuf., vol. 135, pp. 24–37, 2018.

Gökkaya, H.

M. A. Karataş and H. Gökkaya, “A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials,” Defence Technol., vol. 14, no. 4, pp. 318–326, 2018.

Hao, X.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

Hartog, A.

A. Hartog, An Introduction to Distributed Optical Fibre Sensors. Boca Raton, FL, USA: CRC Press, 2017.

He, Y.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

He, Z.

M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.

Hintze, W.

W. Hintze, C. Schutte, and S. Steinbach, “Influence of the fiber cutting angle on work piece temperature in drilling of unidirectional CFRP,” in New Production Technologies in Aerospace Industry, B. Denkena, Ed.New York, NY, USA: Springer, 2013.

Jianshe, Z.

Z. Jianshe, “Measuring and analyzing of drilling temperature for carbon fiber reinforced composites,” Aerosp. Mater. Technol., no. 5, pp. 49–52, 2000.

Karatas, M. A.

M. A. Karataş and H. Gökkaya, “A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials,” Defence Technol., vol. 14, no. 4, pp. 318–326, 2018.

Kempmann, C.

K. Weinert and C. Kempmann, “Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites,” Adv. Eng. Mater., vol. 6, pp. 684–689, 2004.

Kersey, A. D.

A. D. Kerseyet al., “Fiber grating sensors,” J. Lightw. Technol., vol. 15, no. 8, pp. 1442–1463, 1997.

Kim, D.

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

Klinkova, O.

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

Krishnaraj, V.

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.

Le Roux, S.

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

Li, C.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

Li, N.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

Li, Y.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

Liu, G.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

Liu, Q.

M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.

Machado, C. M.

S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.

Mansori, M. E.

J. Xu and M. E. Mansori, “Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite,” Int. J. Adv. Manuf. Technol., vol. 87, pp. 657–675, 2016.

Mansori, M. L.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

Merino-Pérez, J. L.

J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.

Miller, P. W.

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

Ming, W.

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

Mizutani, T.

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

M'Saoubi, R.

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

Okabe, Y.

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

Palmieri, L.

L. Palmieri and L. Schenato, “Distributed optical fiber sensing based on Rayleigh scattering,” Open Opt. J., vol. 7, no. 1, pp. 104–127, 2013.

Poulachon, G.

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

Pramanik, A.

A. Pramaniket al., “Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys—A review,” Compos. Part A, Appl. Sci. Manuf., vol. 101, pp. 1–29, 2017.

Putnam, M. A.

Rajan, G.

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

Ramakrishnan, M.

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

Ramirez, C.

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

Rao, Y. J.

Y. J. Rao, “In-fibre Bragg grating sensors,” Meas. Sci. Technol., vol. 8, no. 4, 1997, Art. no. .

Rech, J.

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

Rossi, F.

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

Royer, R.

J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.

Schenato, L.

L. Palmieri and L. Schenato, “Distributed optical fiber sensing based on Rayleigh scattering,” Open Opt. J., vol. 7, no. 1, pp. 104–127, 2013.

Schutte, C.

W. Hintze, C. Schutte, and S. Steinbach, “Influence of the fiber cutting angle on work piece temperature in drilling of unidirectional CFRP,” in New Production Technologies in Aerospace Industry, B. Denkena, Ed.New York, NY, USA: Springer, 2013.

Semenova, Y.

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

Sharma, M.

A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.

Silva, S.

S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.

Singh, A. P.

A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.

Singh, I.

A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.

Soto, M. A.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

Soutis, C.

C. Soutis, “Fibre reinforced composites in aircraft construction,” Prog. Aerosp. Sci., vol. 41, no. 2, pp. 143–151, 2005.

Steinbach, S.

W. Hintze, C. Schutte, and S. Steinbach, “Influence of the fiber cutting angle on work piece temperature in drilling of unidirectional CFRP,” in New Production Technologies in Aerospace Industry, B. Denkena, Ed.New York, NY, USA: Springer, 2013.

Tai, B. L.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Takabi, B.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Takeda, N.

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

Teixeira, J. P.

S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.

Tsuji, R.

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

Ulrich, R.

W. Eickhoff and R. Ulrich, “Optical frequency domain reflectometry in single‐mode fiber,” Appl. Phys. Lett., vol. 39, no. 9, pp. 693–695, 1981.

Wandro, K. M.

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

Wang, S.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

Wang, Y.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

Wei, W.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

Weinert, K.

K. Weinert and C. Kempmann, “Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites,” Adv. Eng. Mater., vol. 6, pp. 684–689, 2004.

Williams, G. M.

Wu, M.

M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.

Xu, J.

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

J. Xu and M. E. Mansori, “Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite,” Int. J. Adv. Manuf. Technol., vol. 87, pp. 657–675, 2016.

Yashiro, S.

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

Zhou, J.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

Zhu, P.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

Zitoune, R.

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.

Adv. Eng. Mater. (1)

K. Weinert and C. Kempmann, “Cutting temperatures and their effects on the machining behaviour in drilling reinforced plastic composites,” Adv. Eng. Mater., vol. 6, pp. 684–689, 2004.

Aerosp. Mater. Technol. (1)

Z. Jianshe, “Measuring and analyzing of drilling temperature for carbon fiber reinforced composites,” Aerosp. Mater. Technol., no. 5, pp. 49–52, 2000.

Appl. Phys. Lett. (1)

W. Eickhoff and R. Ulrich, “Optical frequency domain reflectometry in single‐mode fiber,” Appl. Phys. Lett., vol. 39, no. 9, pp. 693–695, 1981.

Compos. Part A, Appl. Sci. Manuf. (2)

Y. Okabe, S. Yashiro, R. Tsuji, T. Mizutani, and N. Takeda, “Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates,” Compos. Part A, Appl. Sci. Manuf., vol. 33, no. 7, pp. 991–999, 2002.

A. Pramaniket al., “Joining of carbon fibre reinforced polymer (CFRP) composites and aluminium alloys—A review,” Compos. Part A, Appl. Sci. Manuf., vol. 101, pp. 1–29, 2017.

Compos. Part B, Eng. (1)

A. P. Singh, M. Sharma, and I. Singh, “A review of modeling and control during drilling of fiber reinforced plastic composites,” Compos. Part B, Eng., vol. 47, pp. 118–125, 2013.

Compos. Struct. (4)

R. Zitoune, V. Krishnaraj, F. Collombet, and S. Le Roux, “Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks,” Compos. Struct., vol. 146, pp. 148–158, 2016.

R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Compos. Struct., vol. 92, pp. 1246–1255, 2010.

J. L. Merino-Pérez, R. Royer, and S. Ayvar-Soberanis, “On the temperatures developed in CFRP drilling using uncoated WC-Co tools Part I: Workpiece constituents, cutting speed and heat dissipation,” Compos. Struct., vol. 123, pp. 161–168, 2015.

Q. An, W. Ming, X. Cai, and M. Chen, “Study on the cutting mechanics characteristics of high-strength UD-CFRP laminates based on orthogonal cutting method,” Compos. Struct., vol. 131, pp. 374–383, 2015.

Defence Technol. (1)

M. A. Karataş and H. Gökkaya, “A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials,” Defence Technol., vol. 14, no. 4, pp. 318–326, 2018.

Int. J. Adv. Manuf. Technol. (2)

S. Silva, J. P. Teixeira, and C. M. Machado, “Methodology analysis for evaluation of drilling-induced damage in composites,” Int. J. Adv. Manuf. Technol., vol. 71, no. 9, pp. 1919–1928, 2014.

J. Xu and M. E. Mansori, “Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite,” Int. J. Adv. Manuf. Technol., vol. 87, pp. 657–675, 2016.

Int. J. Mach. Tools Manuf. (2)

R. Fuet al., “Drill-exit temperature characteristics in drilling of UD and MDCFRP composites based on infrared thermography,” Int. J. Mach. Tools Manuf., vol. 135, pp. 24–37, 2018.

N. Li, Y. Li, J. Zhou, Y. He, and X. Hao, “Drilling delamination and thermal damage of carbon nanotube/carbon fiber reinforced epoxy composites processed by microwave curing,” Int. J. Mach. Tools Manuf., vol. 97, pp. 11–17, 2015.

J. Lightw. Technol. (1)

A. D. Kerseyet al., “Fiber grating sensors,” J. Lightw. Technol., vol. 15, no. 8, pp. 1442–1463, 1997.

Materials (1)

S. A. Ashrafi, P. W. Miller, K. M. Wandro, and D. Kim, “Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite,” Materials, vol. 9, 2016, Art. no. .

Meas. Sci. Technol. (1)

Y. J. Rao, “In-fibre Bragg grating sensors,” Meas. Sci. Technol., vol. 8, no. 4, 1997, Art. no. .

Open Opt. J. (1)

L. Palmieri and L. Schenato, “Distributed optical fiber sensing based on Rayleigh scattering,” Open Opt. J., vol. 7, no. 1, pp. 104–127, 2013.

Opt. Lett. (1)

Procedia CIR (1)

C. Ramirez, G. Poulachon, F. Rossi, and R. M'Saoubi, “Tool wear monitoring and hole surface quality during CFRP drilling,” Procedia CIR, vol. 13, pp. 163–168, 2014.

Procedia Manuf. (2)

J. Xu, C. Li, M. L. Mansori, G. Liu, and M. Chen, “Study on the frictional heat at tool-work interface when drilling CFRP composites,” Procedia Manuf., vol. 26, pp. 415–423, 2018.

F. Chegdani, B. Takabi, B. L. Tai, M. L. Mansori, and S. T. S. Bukkapatnam, “Thermal effects on tribological behavior in machining natural fiber composites,” Procedia Manuf., vol. 26, pp. 305–316, 2018.

Prog. Aerosp. Sci. (1)

C. Soutis, “Fibre reinforced composites in aircraft construction,” Prog. Aerosp. Sci., vol. 41, no. 2, pp. 143–151, 2005.

Sensors (2)

M. Ramakrishnan, G. Rajan, Y. Semenova, and G. Farrell, “Overview of fiber optic sensor technologies for strain/temperature sensing applications in composite materials,” Sensors, vol. 16, no. 1, 2016, Art. no. .

Z. Dinget al., “Distributed optical fiber sensors based on optical frequency domain reflectometry: A review,” Sensors, vol. 18, no. 4, 2018, Art. no. .

Tribol. Int. (1)

O. Klinkova, J. Rech, S. Drapier, and J. Bergheau, “Characterization of friction properties at the workmaterial/cutting tool interface during the machining of randomly structured carbon fibers reinforced polymer with carbide tools under dry conditions,” Tribol. Int., vol. 44, pp. 2050–2058, 2011.

Other (6)

M. Wu, X. Fan, Q. Liu, and Z. He, “Quasi-distributed fiber-optic acoustic sensor using ultra-weak reflecting point array,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF19.

A. Hartog, An Introduction to Distributed Optical Fibre Sensors. Boca Raton, FL, USA: CRC Press, 2017.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “Monitoring of the drilling-induced temperature profile in CFRP plates using distributed optical fiber sensing,” in Proc. 26th Int. Conf. Opt. Fiber Sens., Lausanne, Switzerland, 2018, Paper WF97.

P. Zhu, Y. Li, Y. Wang, S. Wang, W. Wei, and M. A. Soto, “High resolution drilling-induced temperature mapping of CFRP laminates using a fully distributed optical fiber sensor,” in Advances in Condition Monitoring of Machinery in Non-Stationary Operations, A. Fernandez Del Rincon, F. Viadero Rueda, F. Chaari, R. Zimroz, and M. Haddar, Eds. Cham, Switzerland: Springer, 2019.

X. Fan, “Distributed Rayleigh sensing,” in Handbook of Optical Fibers, G. D. Peng, Ed. Singapore: Springer, 2018.

W. Hintze, C. Schutte, and S. Steinbach, “Influence of the fiber cutting angle on work piece temperature in drilling of unidirectional CFRP,” in New Production Technologies in Aerospace Industry, B. Denkena, Ed.New York, NY, USA: Springer, 2013.

Cited By

OSA participates in Crossref's Cited-By Linking service. Citing articles from OSA journals and other participating publishers are listed here.