Abstract

A novel, to the best of our knowledge, method of wet chemical etching of sapphire workpieces (such as optics, wafers, windows, and cones), called the sapphire advanced mitigation process (or sapphire AMP), has been developed that exposes sub-surface mechanical damage created during the optical fabrication process and significantly enhances the surface laser damage resistance ($ \gt {2{\times}}$) and mechanical strength (up to $\sim{2.6{\times}}$). Sapphire AMP involves first treating the workpiece with a mixture of sulfuric and phosphoric acid $([{\rm H_{2}{\rm SO_{4}}}]:[{\rm H_{3}{\rm PO_{4}}}]=1:3)$ at 220°C, followed with phosphoric acid at 160°C, then with sodium hydroxide base (NaOH) and surfactant at 40°C, and finally with a high-pressure deionized water spray rinse. Sapphire AMP has been demonstrated on both A- and C-plane sapphire workpieces. The mechanism of this etch process involves the reaction of the sapphire $({\rm Al_{2}}{\rm O_{3}})$ surface with sulfuric acid $({\rm H_{2}}{\rm SO_{4}})$ forming aluminum sulfate $[{{\rm Al}_2}{({{\rm SO}_4})_3}]$, which has low solubility. The high phosphoric acid content in the first and second steps of sapphire AMP results in the efficient conversion of ${{\rm Al}_2}{({{\rm SO}_4})_3}$ to aluminum phosphate $({\rm AlPO_{4}})$, which is very soluble, greatly reducing reaction product redeposition on the workpiece surface. Sapphire AMP is shown to expose sub-surface mechanical damage on the sapphire surface created during the grinding and polishing processes, whose etched morphology has either isotropic or anisotropic evolution depending on the nature of the initial surface damage. Sapphire AMP was also designed to remove the key known surface, laser absorbing precursors (namely, foreign chemical impurities, the fracture surface layer of preexisting sub-surface damage, and reaction product or foreign species redeposition or precipitation). Static and sliding indention induced surface microfractures on sapphire are shown after sapphire AMP to have a significant decrease in the fast photoluminescence intensity (a known metric for measuring the degree of laser damaging absorbing precursors). In addition, the onset of laser damage (at 351 nm 3 ns) on sapphire AMP treated workpieces was shown to increase in fluence from $\sim{4}$ to $ \gt {9}.{5}\;{{\rm J/cm}^2}$. Finally, biaxial ball-on-ring mechanical tests on sapphire disks showed an increase in the failure stress from 340 MPa (with pre-existing 28 µm flaws) to $\sim{900}\;{\rm MPa}$ after sapphire AMP, which is attributed to the blunting of the surface microfractures.

© 2020 Optical Society of America

Research on the mitigation of redeposition defects on the fused silica surface during wet etching process

Changpeng Li, Ke Yang, Zhuo Zhang, Yuejie Qian, Taixiang Liu, Hongwei Yan, Jin Huang, Lin Yao, Yinbo Zheng, Xiaodong Jiang, and Wanguo Zheng
Opt. Express 32(6) 8638-8656 (2024)

Reaction ion etching process for improving laser damage resistance of fused silica optical surface

Laixi Sun, Hongjie Liu, Jin Huang, Xin Ye, Handing Xia, Qingzhi Li, Xiaodong Jiang, Weidong Wu, Liming Yang, and Wanguo Zheng
Opt. Express 24(1) 199-211 (2016)

Towards high-optical-strength, fluorine-resistant coatings for intracavity KrF laser optics

Vladimir Zvorykin, Radmir Gaynutdinov, Mikhail Isaev, Dmitry Stavrovskii, and Nikolai Ustinovskii
Appl. Opt. 59(5) A198-A205 (2020)

Investigation of laser-induced damage threshold improvement mechanism during ion beam sputtering of fused silica

Mingjin Xu, Feng Shi, Lin Zhou, Yifan Dai, Xiaoqiang Peng, and Wenlin Liao
Opt. Express 25(23) 29260-29271 (2017)

Effect of etching morphology of artificial defect on laser-induced damage properties under 355  nm laser irradiation

Bin Ma, Menglei Lu, Guangda Zhan, Ke Wang, Xinbin Cheng, and Zhanshan Wang
Appl. Opt. 54(11) 3365-3371 (2015)